Hangar 9 P-51D Blue Nose 60 ARF - Manual (Page 3)

The Spektrum trademark is used with permission
of Bachmann Industries, Inc.
4 Hangar 9 P-51 Mustang 60 ARF Assembly Manual 5 Hangar 9 P-51 Mustang 60 ARF Assembly Manual
Recommended Setup–2-Stroke Glow
• Evolution ® .61NX with Muffler (EVOE0611)
• Evolution Propeller 12 x 6 (EVO12060)
• Fuel Dot (HAN115)
Recommended Setup–4-Stroke Glow
• Saito ™ 1.25 AAC w/Muffler (SAIE125A or SAIE125AGK)
• Evolution Propeller 15 x 6 (EVO15060)
or
16 x 6 (EVO16060)
• Fuel Dot (HAN115)
• Muffler 90-Degree Adapter (SAI120S140)
Recommended Setup–4-Stroke Gas
• Saito ™ FG-20 4-Stroke Gas Engine (SAIEG20)
• Evolution Propeller 15 x 6 (EVO15060)
or
16 x 6 (EVO16060)
• Fuel Dot (HAN115)
• Muffler 90-Degree Adapter (SAI120S140)
• JR Switch, Chargeswitch (JRPA004)
• Ignition battery, 6-volt 2300mAh (JRPB5006)
Recommended Setup–
Power 60 (EP)
• E-flite ® Power 60 BL Outrunner Motor (EFLM4060A)
• 60-Amp Speed Control (EFLA1060)
• APC Propeller 15 x 8E (APC15080E)
or
• APC Propeller 15 x 10 (APC15010E)
• Li-Po Battery, 5000mAh 6-Cell/6S 22.2V
(THP50006SP30)
Recommended Setup–
Power 90 (EP)
• E-flite ® Power 90 BL Outrunner Motor (EFLM4090A)
• 85-Amp Speed Control (CSEPHX85HV)
• 20mm Spacer for Power 90 (HAN242030)
• APC Propeller 16 x 8 (APC16080E)
• Li-Po Battery, 5000mAh 4-Cell/4S 14.8V (2)
(THP50004SP30)
Field Equipment Required
• Fuel (15% recommended)
• Long Reach Glow Plug Wrench (HAN2510)
• Metered Glow Driver w/Ni-Cd & Charger (HAN7101)
• 2-Cycle Sport Plug (EVOGP1)
• Manual Fuel Pump (HAN118)
Optional Field Equipment
• Self-stick weights, 6 oz (HAN3626)
• PowerPro 12V Starter (HAN161)
• 12V 7Ah Sealed Battery (HAN102)
• Power Panel (HAN106)
• Blue Block After Run Oil (EVOX1001)
• Cleaner and towels
Additional Required Tools
Drill File
Pin drill Pliers
Ruler Hobby scissors
Side cutters Epoxy brushes
Felt-tipped pen Rotary tool
Cutoff wheel Sanding drum
String/dental floss T-pins
Mixing sticks Mixing cups
Paper towels Rubbing alcohol
Petroleum jelly Covering iron
Hobby knife with #11 blade Small clamps
Medium grit sandpaper
Z-bend Pliers (HAN119)
Phillips screwdriver: #1, #2 Hook and loop tape
Hook and loop strap
Pencil
Water pump pliers Two-sided tape
Tie wrap, 8-inch (203mm)
Tie wrap, 12-inch (305mm)
Low-Tack Tape (MMM209034)
Box end or open end wrench: 12mm, 11/32-inch
Hex wrench or ball driver: 3/32-inch
Drill bit: 1/16-inch (1.5mm), 5/64-inch (2mm), 5/32-inch
(4mm), 7/32-inch (5.5mm), 1/4-inch (6mm)
Additional Required Adhesives
Canopy Glue (PAAPT56)
Medium CA (PAAPT02)
Thin CA (PAAPT08)
Threadlock (PAAPT42)
30-Minute Epoxy, 8 oz (PAAPT39)
Hinge Glue (PAAPT55)
FS One®
With FS One (HANS2000) you get more than photorealistic
fields, gorgeous skies and realistic-looking aircraft. You get
incredibly advanced aerodynamic modeling that simulates
every possible aspect of real-world flight.
The first Hangar Pack
® (HANS4010) will add even more
aircraft to FS One. This latest edition includes ten new planes
and helis from your favorite brands, including Hangar 9,
E-flite and Align. You’ll be able to fly aircraft that are only
available on FS One such as the T-REX, Blade CX2, Blade CP
Pro, Hangar 9 P-51 and F-22 PTS. And as always, with the
Hangar Pack, you still get all the same great features that
you did with the original aircraft.
HANS2008 HANS4010
Using the Manual
This manual is divided into sections to help make assembly
easier to understand, and to provide breaks between each
major section. In addition, check boxes have been placed
next to each step to keep track of each step completed.
Steps with a single box () are performed once, while steps
with two boxes () indicate that the step will require
repeating, such as for a right or left wing panel, two servos,
etc. Remember to take your time and follow the directions.
Before Starting Assembly
Before beginning the assembly of your model, remove
each part from its bag for inspection. Closely inspect the
fuselage, wing panels, rudder and stabilizer for damage. If
you find any damaged or missing parts, contact the place of
purchase.
If you find any wrinkles in the covering, use a heat gun or
covering iron to remove them. Use caution while working
around areas where the colors overlap to prevent separating
the colors.
HAN100 – Heat Gun
HAN150 – Covering Glove
HAN101 – Sealing Iron
HAN141 – Sealing Iron Sock
Your model is covered in a printed version of UltraCote
developed specifically for your P-51 Mustang. It has all the
same properties as the glossy versions of UltraCote. All the
instructions provided with our original UltraCote apply to this
new and exciting product.
Important Information
Regarding Warranty Information
Please read our Warranty and Liability Limitations section on
Page 67 before building this product. If you as the purchaser
or user are not prepared to accept the liability associated
with the use of this Product, you are advised to return this
Product immediately in new and unused condition to the
place of purchase.
Transmitter Requirements
The P-51 Mustang requires a minimum of a 7-channel radio
to operate all the functions of your aircraft. We suggest the
following radio systems available through Horizon Hobby or
your local hobby distributor.
Spektrum DX7 SPM2710
JR Systems X9303 2.4GHz JRP2915
JR Systems 12X 2.4GHz JRP1200
Radio Equipment Requirements -
7-Channel Receiver
The following items are recommended when installing the
7-Channel AR7000 receiver (SPM6070) in your aircraft:
DS821 Digital Sport Servo (6) JRPS821
(Note: Only 6 servos required for EP version)
DS821 Digital Sport Servo Reverse (Flap) JRPS821R
RT88 Retract Servo (2) JSP20080
3-inch Servo Extension (2) JSP98100
6-inch Servo Extension (2) JSP98110
12-inch Servo Extension (2) JSP98030
Y-Harness (2) JSP98020
JR Switch, Chargeswitch JRPA004
Receiver battery, 6-volt, 2700mAh JRPB5008
Flaps: DS821 Servo and DS821 Servo/Reverse
• Y-harness (plugged into receiver)
Retracts: RT88 Servo (2)
• 3-inch Extension (plugged into receiver) (2)
• 6-inch Extension (connected to servo) (2)
Ailerons: DS821 Servo (2)
• Y-harness (plugged into receiver)
• 12-inch Extension (connected to servo) (2)
Rudder: DS821 Servo
Elevator: DS821 Servo
Throttle: DS821 Servo
Radio Equipment Requirements -
9-Channel Receiver
The following items are recommended when installing the
9-Channel AR9000 receiver (SPM9000) in your aircraft:
DS821 Digital Sport Servo (7) JRPS821
(Note: Only 6 servos required for EP version)
RT88 Retract Servo (2) JSP20080
3-inch Servo Extension (6) JSP98100
6-inch Servo Extension (2) JSP98110
12-inch Servo Extension (2) JSP98030
JR Switch, Chargeswitch JRPA004
Receiver battery, 6-volt, 2700mAh JRPB5008
Flaps: DS821 Servo (2)
• 3-inch Extension (plugged into receiver) (2)
Retracts: RT88 Retract Servo (2)
• 3-inch Extension (plugged into receiver) (2)
• 6-inch Extension (connected to servo) (2)
Ailerons: DS821 Servo (2)
• 3-inch Extension (plugged into receiver) (2)
• 12-inch Extension (connected to servo) (2)
Rudder: DS821 Servo
Elevator: DS821 Servo
Throttle: DS821 Servo
Optional Accessories
• 1/6 US WWII Pilot (HAN8297)
• Decal Sheet, Petie 2nd,
P-51 60 Blue Nose ARF HAN24227
• Decal Sheet, Excalibur,
P-51 60 Blue Nose ARF HAN24228