Panasonic OMNIVISION PV-4661 - Manual (Page 19)

Cancel a Timer Recording:
Recording is in progress
1
Push the VCR POWER button to
release the VCR from timer mode,
2
Push the STOP button within 10
seconds of pushing the VCR Power
button to cancel the recording.
The TIMER indicator goes out in the
Multi- Function display.
Replace Program Contents:
Recording is not in progress
1 Push the PROG
button to display
all currently set
programs.
P DT STRAT STOP CM SPD 1----------- --
a:OOP 9;00P 10 SP
Q:00P10:00P L SLP
Rotate and push the
Wheel to select and
enter the desired
timer recording.
(See page 18.)
Rotate and push the
Wheel to select and
enter replacement
information.
3 10
su
SELECT t-8:ROTATE WHEEL
ENTER
CANCEL
END
;PUSH WHEEL
;PUSH CLEAR KEY
rPUSH PHOa KEY
QATEi. START STOP CH
8 SAT 10:00P12:00P 125
SLP
SELECT START DATE
BY HOTATINU WHEEL
♦PUSH CLEAR : PUSH WHE6L-P
TO B40 PUSH PROG KEY
Push the PROG button to exit this mode
and return to the normal TV screen.
Review or Ciear Program Contents:
Recording is not in progress
Push the PROG
button to display
all currently set
programs.
Rotate the Wheel to
select the desired
program number.
Push the CLEAR
button to clear the
program.
P DT STRAT STOP CH SPO
U.JA'JMI.i.HU.l.M.im'y
2 8 10:OOP12:OOP12S SLP
3 10 8:OOP 9:00P 10 SP
4 SU 9:00PI0:00P L SLP
SELECT 1-8:R0TATE WHEEL
ENTER :PUSH WHEEL
CANCEL :PUSH CLEAR KEY
END ;PUSH PROG KEY
P OT STRAT STOP CH SPD
□-------------:------------— —
2 8 10:OOP12;OOP125 SLP
3 10 e.-OOP 9;00P 10 SP
4 SU 9:00P10:00P L SLP
SELECT 1-8:HOT ATE WHEEL
ENTER :PU$H WHEEL
END :PUSH PROG KEY
Push the PROG button to exit this mode and
return to the normal TV screen.
Timer Recording
Using VCR Buttons
A timer recording can be set up using the buttons on the
VCR. If necessary, the clock can also be set.
Hold down
REC/TIME.
and
i Push FF to
t enter the
: program mode.
START STOP CH|
SLP I
ELECT START DATE
BY SELECT A/T KEY
NEXT. PUSH SET KEY OR
TO END PUSH PROG KEY
If the clock is not set, pushing these
buttons will display the SET CLOCK
screen. In this case, proceed with steps
2 and 3 to set the clock and then steps
2"-6 to set a timer recording.
Once the VCR is in the Program mode, the PLAY, REC, FF,
and REW buttons on the VCR operate only as specified above
-M y -- set clock
/IN DST:0N
SELECT MONTH
BY SELECT KEY
NEXT, PUSH SET KEY OR
TO END PUSH PROG KEY
® (8
or
{for down) {for up)
Push REW or PLAY to
make your selection.
S)
Push FF to set
and move on to
the next item.
Push SET (FF) repeatedly to move to a
particular item for setting or correction.
Items to be Set:
• recording DATE
• START time
• STOP time
• CH(annel), or LINE
• SPEED (SP, LP, SLP)
When the program is completed...
Push REGIME
and FF to display
program contents. and
(at the same time).
To set the next program,
repeat steps 2, 3, and 4 before continuing with step 5.
(0) and ^
(at the same time)
Push REC/TIME and
FF to exit this mode.
Push POWER off
to set the timer.
N. I >*
Multi Function Display
It is not possible to clear a timer program using the VCR buttons.
Please use the Remote Control.
When recording programs via a cable box. make sure the cable
box is left on. If the Cable box cannot be controlled with the VCR,
you must manually select the desired channel.
19