Panasonic OMNIVISION PV-HD1000 - Manual (Page 33)

Reset Channel, Clock
To Add or Delete a Channel
1 Select a channel using the
NUMBERED keys to add
or CH A/ T to delete.
2 Press ADD/DLT to add
or delete the channel.
• To select a channel
once it’s deleted,
use the NUMBERED keys
on the remote control.
To Set or Reset the Clock
In case the clock is wrong, or a power failure occurred.
1 Press ACTION to display
the menu.
2 Press AT to select “SET
CLOCK," and then press
► to display the “SET
CLOCK” screen.
3 Press AT to select
“MANUAL,” and then
press ► to display the
SET CLOCK screen.
4 Press AT and ► to
select and set the date,
time and DST.
(Daylight Saving Time).
5 Press ACTION twice to
start the clock and exit
this mode.
-------------- MENU -.......... —
SET UP VCR
SET UP CHANNEL
--------- SET CLOCK ---------
AUTO CLOCK SET
SELECT:* T KEY
SET :► KEY
END lACTION KEY
--------- SET CLOCKNk^--N47'
1/ 4/2000 TUE 12:(
SELECT:* T KEY
SET ► KEY
END ;ACTION KEY
For Auto Clock Set, select "AUTO CLOCK SET,”
and then follow the One Time D-VHS VCR Setup
instructions on pages 12-14.
To Replace Channels in Memory
In case you have cable installed, etc.
1 Press ACTION to display
the menu.
2 Press AT to select "SET
UP CHANNEL," and then
press ► to display the
"SET UP CHANNEL” screen.
3 Press AT to select
“ANTENNA," and then
press ► to set your antenna
system (TV or CABLE).
4 Press AT to select “AUTO
SET,” and then press ►
to display the “CHANNELi
CLOCK AUTO SET’ screen.
-------------- MENU --------------
SET UP VCH
SET CLOCK
SELECT:* ▼ KEY
SET ; ► KEY
END ;ACTION KEY
------SET UP CHANNEL------
FJJbijJliH : CABLE
AUTO SET
CABLE/DSS BOX SET UP
VCR PIUS+ CH SET UP
SELECT:* ▼ KEY
SET :► KEY
END :ACTION KEY
CHANNEL/CLOCK AUTO SET
CONNECT ANTENNA CABLE
AND IF YOU USE A CABLE
BOX, TUNE I T TO YOUR
LOCAL PBS CH THEN, . .
PLEASE PUSH CH UP KEY
5 Follow the One Time
D-VHS VCR Setup
instructions on pages 12-14.
• Clock Auto Set will be
performed when channels
are replaced in memory.
To cancel, press STOP when “AUTO CLOCK
SET PROCEEDING” appears on-screen.
To Setup the D-VHS VCR in Case a Cable
Box or DSS Receiver was Installed or
Replaced
1 Press ACTION to display
the menu.
Press AT to select “SET
UP CHANNEL,” and then
press ► to display the “SET
UP CHANNEL” screen.
SET UP VCR
SET CLOCK
UH=f II
------ SET UP CHANNEL -----
CABLE ANTENNA :
AUTO SET
VCR Plus+ CH SET UP
ARE YOU USING A CABLE
BOX OH DSS RECEIVER?
NO
SELECT HOOKUP
VCR*CABLE/DSS BOX*TV
SELECT
SET
END
* ▼ KEY
► KEY
ACTION KEY
3 Press AT and T to select
and set “CABLE/ DSS BOX
SET UP," and then select
and set your connection type
• If you selected “NO", go to
“Alternate Instructions” on
page 14.
• To exit this mode, press
ACTION three times.
4 Press AT and ► to select
and set “CABLE/DSS BOX
► VCR►TV,”and then
continue with steps 4-7 on pages 12, 13.
If these steps are completed,
the “SET UP CHANNEL" screen will appear.
When Using the 100 key
When selecting CABLE channels 100 to 125 with the
NUMBERED keys, first press the 100 key and then
enter the remaining two digits.
For example, to select channel 125:
Press NUMBERED keys 100, then 2, then 5.
Some screens shown above may not be displayed during digital playback.
This D-VHS VCR will accurately maintain its calendar up to Dec. 31,2097,11:59PM.
Normal TV or Cable channels are automatically selected and placed in memory depending on how your
D-VHS VCR is hooked up.
If you change your Cable Box or DSS Receiver, please perform the “Auto Clock Set" section on pages 12 and 13.
33