Panasonic OMNIVISION PV-HD1000 - Manual (Page 22)

VCR Plus+ System Setup
•Important: If the remote control POWER, ACTION, PROG, CHA/T, INDEX or ADD/DLT button does not work when
pressed, press the VCR button on the remote and try the button again.
In order tor the D-VHS VCR to read the VCR Plus+ code, some set up is required. A Guide (VCR Plus+) channel
number is assigned to each local broadcast and cable station. Because this number sometimes differs from the
channel your TV receives the station on, it is necessary to program the D-VHS VCR with local channel information.
Channel Setup Preparations
NOTE: Complete the steps on this page if your
cable box can be controlled with the D-VHS
VCR, or your D-VHS VCR hook-up resembles
“B” on page 10.
Prepare a list like the example below.
This list will help you smoothly enter the information
needed in step “4" at right.
You will need the following to complete the list:
■ A line up of normal and/or cable stations you
receive along with the channel numbers your TV
receives them on. A cable channel line-up chart
is supplied by your cable company.
■ A list of Guide (VCR Plus+) channel numbers
assigned to the stations you receive. This list is
available in
TV Guide and the TV listings found
in selected newspapers.
1 Make a chart with 3 columns like the example
below. In the left column, fill in the name or call
letters of the stations you receive.
2 In the middle column, fill in each station’s
assigned Guide (VCR Plus+) number found in
TV Guide, newspapers, etc.
3 In the right column, fill in the channel number
that your TV receives the station on from your
channel line-up.
EXAMPLE ONLY
Broadcast or
Cable
Station Name
Assigned
Guide
(VCR PIUS+)
channel no.
Channel
no.your TV
receives the
station on
HBO 33 15
Nickelodeon 38 20
CBS 04 04
\ FOX 11
VCR Plus+ Channel Setup
Complete this page only if Type B
connection method (pg. 10) is used.
• Before you begin, complete the Channel Setup Preparations
below left.
Important Note:
If your D-VHS VCR connection type changes from type A to B,
perform “To Setup the D-VHS VCR in Case a Cable Box or DSS
Receiver was Installed or Replaced’’ section on page 33 before
proceeding with these steps.
1
Press ACTION* to display
the menu.
2
Press AT to select “SET UP
CHANNEL,” and then press
---------------- MENU -----------------
SET UP VCR
SET CLOCK
шшввгишш
SELECT:* ▼ KEY
SET ;^ KEY
END lACTION KEY
► to display the “SET UP CHANNEL” screen.
Press AT to select “VCR
Plus-i- CH SET UP,” and then
press ► to display the “VCR
Plus-i- CH SET UP” screen.
------- SET UP CHANNEL ---------
ANTENNA : CABLE
AUTO SET
CABLE/DSS BOX SET UP
SELECT:* ▼ KEY
SET :► KEY
END :ACTION KEY
IMPORTANT NOTE:
For step “4,” use the list you prepared. You may leave
lines blank if you don’t receive that station, or if the
GUIDE CH number and the CABLE
(or TV) CH numbers are the same.
4 Press ► to move the shaded
area to the right side.
Then, press AT to change
CABLE or TV CH number.
Next, press “4 to set the number.
Now, press AT
to continue.
Repeat this operation untii the list
is compiete.
VCR Hus+ CH SET UP
GUIDE CH CABLE CH
* SB - -
02 —
SELECT * ▼ KEY
SET ► KEY
END ACTION KEY
VCR PIUS+ CH SET UP
GUIDE CH CABLE CH
* 01 Ш 02
SELECT:* ▼ KEY
SET :
•* KEY
END :ACT ION KEY
To Enter More Programs
Press AT and ► to seiect the incorrect CABLE or TV CH number.
Then, press AT to change, or ADD/DLT to delete the channel.
5
Press ACTION three times to exit
the VCR PIUS4- CH SET UP mode.
(NOTES
Make each entry within 5 minutes or the D-VHS VCR
will leave this mode.
Once local channels have been programmed, they will
stay in memory, even in the case of a power failure.
"^VCR PI us - h C^ and PlusCode are registered trademarks of Gemstar
Development Corporation. The VCR Plus-r system is manufactured
under license from Gemstar Development Corporation.
22