Panasonic OMNIVISION PV-HD1000 - Manual (Page 20)

Timer Recording
^Important; If the remote control
work when pressed,
You can set up the D-VHS VCR to record a one
time, daily, or weekly program while you are
away or otherwise occupied. Up to 8 programs
can be stored in memory.
[^^Check list before you begin.
Q All connections are made.
(See pages 6-11.)
n TV and D-VHS VCR are plugged in and
turned on.
^ VCR/TV selector is set to “VCR.”
Clock is set to correct time.
Record tab in place. (See page 34.)
^ When Digital Timer Recording, use the
D-VHS cassette tapes.
important notes when using a
DSS receiver
• When recording programs via a DSS
receiver, the DSS receiver must be left on.
• When recording programs via an antenna or
cable, the DSS receiver must be turned off.
POWER, ACTION, PROG, CHA/T, INDEX or ADD/DLT button does not
press the VCR button on the remote and try the button again.
1
Press PROG* to display the
“SET PROGRAM” screen.
Press AT to select ‘TIMER
PROGRAM,” and then press ►
to display the program screen.
* If a program is already in memory, press AW
and ► to select an unused program number.
-------- SET PROGRAM---------
VCR PIUS+ PROGRAM
SELECTS ▼ KEY
SET ;► KEY
END ;PROG KEY
START STOP CH
3
Press AT and
►
to select and
set one of the following:
• 1-31 =One time recording
• DAILY =Same time MON-FRI
• WEEKLY (SUN-SAT) =Same time once a week
Example ^^8—9....... 3i— i — 2 6—^
Today’s Date----- 7 SELECTA/V Selactlon order DAILY
L WEEKLY WEEKLY WEEKLY J
^ (SAT) (MON) (SUN)
ESQ
SELECT:* » KEY
SET ;► KEY
ENO : PROG KEY
4
Press AT and to
select and set each of the
remaining items at right.
If you want to record digital TV,
channel selection should be "OTV.”
Remaining Items to be set;
• START time • STOP time
• CH(annel) number, DTV or
LINE for outside source recording
• Speed (SP, LP, SLP)
To Make Corrections
Repeatedly press ► to move the cursor to the right, or ^ to
move to the left to the incorrect entry and make the correction,
D Press PROG to end the program.
• This screen appears for confirmation.
If you use a DSS receiver and enter a
channel number of 100-125, the screen
at right appears.
Press AT to select “DSS" or
“CABLE,” and then press ► to enter.
• The confirmation screen appears
above right after this selection.
To Enter More Programs
Press AW and ► to select and set a blank
program number, and then repeat steps 3 and 4.
6
Press PROG to exit this mode.
Press POWER off to set the timer.
• When recording programs via a cable
box, make sure the cable box is left
ON and tuned to the desired channel.
-¡¡11112-
Multi Function Display
• For DTV Timer Recordina. make sure the set
too box fTU-DST50) IS left ON, and turned to
the desired channel. On the VCR, D-VHS
switch IS set to HS or HS/STD and oower is off.
NOTES
Digital programs which have copy protect data cannot be recorded.
A cassette with no record tab is ejected and “TIMER” flashes when the power is turned off to set the timer.
If the start times of two programs overlap, the lower numbered program will have priority.
If the start time for a timer recording comes up during a normal recording or One Touch Recording (pages 16,17,
19), the timer recording will not be performed.
If there is a power interruption of more than one minute, the recording will not be performed or continue.
If a timer recording by the D-VHS VCR and by the Set Top Box overlap, only the earlier program will be performed.
20