Panasonic CF-E1M User Manual

Panasonic Computers

Table of contents

Document Outline

OPERATING INSTRUCTIONS
Model No. CF-E1M
- Introduction
- Illustrations in this Manual
- ( Enter 1 :
- Copyright
- Disclaimer
- Trademarks
Read Me First
- Federal Communications Commission Radio Frequency Interference Statement
- Warning
- FCC Regulation Notice for modem
- Read Me First
  - Usage
  - Handling
- Read Me First
Names and Functions of Parts
- Reset Button | ^
- RAM Module Slot
- USB Ports I
- Optical Digital Audio Output Terminal
- Dust Protection Cap
- Names and Functions of Parts
First-time Operation
- 1 Confirm the inclusion of all parts
- First-time Operation
- First-time Operation
  - 8 Setup Windows 98
  - Q Computer power off
Using the Mouse
- Basic Operation
Starting Up/Shutting Down
- Starting Up
- Shutting Down (power off your computer)
  - Confirm that 0; is displayed on the taskbar
  - Turn your computer off
- starting Up / Shutting Down
Conserving Power
- Setting Power Management
Setting the Sound Volume
- Using the Audio Mixer
  - Select ^ from the taskbar
- Making Settings In the Control Panel
DVD-ROM Drive
- Usage Precaution
  - To avoid damaging discs:
- Using the DVD-ROM Drive
Modem
- Connecting to a Telephone Line and Settings 1 Connecting a telephone line to the internal modem
- 2 Select [Dialing Properties] in [Start] - [Settings] - [Control Panel] - [Modems]
VisualBright
- When you want to turn this feature off
  - Maximized high image quality display 1
  - 10% of the width of the window
Using USB Devices
- When Installing a New Device Driver
- Using the Floppy Disk Drive
  - 1 Connecting a floppy disk drive.
- Inserting / Removing the Floppy Disk
  - Using USB Devices (e.g., Floppy Disk Drive, Printer)
- Using the Printer
Using PC Cards
- When inserting a card
  - Press the ejection button and remove the dummy card (g* below)
  - Set the labeled side of the PC Card to the rear of the display and slide the card firmly into the slot
- Removing the PC Card
Using Audio Devices
- Microphone / Headphone / Speaker
- Optical Digital Audio Output Terminal
  - To connect a device, perform the following steps:
Adding Memory
- After completing operations and power off the computer (page 17), remove the AC cord
- Set the computer so that the display is facing downwards Using a small-sized Philips screwdriver, remove the four screws
  - Soft Cloth
- Adding Memory
DV Capture
- Connecting a Digital Video Camcorder
- When Removing the Digital Video Camcorder
- Before Running DV Capture
- Running DV Capture
  - Confirm that the digital video camcorder is properly connected
  - Select [DV Capture] icon on the desktop
- DV Capture
  - Movie Capture
  - Playing Captured Movie Files
    - Running DV Capture {or page 37)
- DV Capture
- DV Capture
  - Detailed Settings for Stili Image Capturing
    - Running DV Capture {o= page 37)
    - Select [Settings] and then [Still Settings] Make the still image settings and click [OK]
  - Changing the destination folder and file name
Using Image Files
- NOTE>
- Running ImageBrowser
  - Select [IMAGEBROWSER] icon on the desktop
- Using Image Files
- Using Image Files
  - Sending Mail From a List
    - 1 Running ImageBrowser (c^ page 43)
      - 0 Click the still image to send by mail
    - Write a message and then send the mail
  - Compressing and Mailing Moving Images (Movie Messenger)
    - 1 Open Movie Messenger from the ImageBrowser (c^ page 43)
    - Make the compression settings and compress the file
      - 0 Make the compression settings
      - Click [Compress]
- Using Image Files
  - Run the mail software
    - ® Click [Play]
    - Click [E-mail]
Setup Utility
- Running the Setup Utility
- Setup Utility
  - Main Menu
    - 1 Select [Main] menu with [ ^ I [ -» I keys
  - Security Menu
List of Error Codes
Dealing With Problems
- # When the display freezes
Troubleshooting Suggestions
- Starting Up
- Operations
- Troubleshooting Suggestions
- Troubleshooting Suggestions
  - Connecting Peripherals
  - System File Checker
Reinstalling Software
- Before Reinstallation
- Reinstallation
- Reinstalling Software
Installing Windows 98 Related Files
- 1 Install the driver to use the DVD-ROM drive in the MS-DOS mode
- 2 Turn the computer on
- 3 If the [Panasonic] logo disappears, immediately press C Ctrl ] key (until the menu is displayed)
- Select [Command prompt only]
- Set the Product Recovery CD-ROM in the DVD-ROM drive After C:\>, type in the following
- Follow the on-screen instructions
Specifications
- Main Specifications
- Other Specifications
- For U.S.A.