Panasonic SC-DV150 - Manual (Page 45)

(A
c
•s
V
8-
a
ÎC
Tï
§
o
s
tr
"0
§
<8
■ ' ■.í"/^-.-.' .. ■ •-.■■ ■ ■ ■■ .■'! •.■..■ ■.
O d ф ь
G-0 t ©-0
©-©J© 6
0 ©.© o
neHv >L Kmm
Q
oOp
ü 0* d
TKP 5SJf JEL JÍtSL
Q O o O
B 5 ¿ le
ffi □ a
■)$3^SM.rn
E:;íí.tSíS¿aft?iK;;ffi
SÍ:B;fS'?Í|s4®Sr ÎT0^Qll^ÿ-
iSlllï
©
09 . ciScT
% ÿ’KJÂSJMM
y,
c. ^ ,- I / I II
..... ÿ. )' U U
-^SSSi‘Sai^îi
O
o^d
L c M
I I Ì I III -■,.;
"I O O St : tо
/ ( 77 '■■п::,?о'iв>fr;)
L l—i ±1 ,'
V I'" ■ ^ =’;] '^r, Ï 'S,i:-. i v -;■?. ; r,.;i'r.' ^
■. ^1Wf f -W№-^ . p ■ ; ■■ J.: ./.v ■' v'-.;. -.>y, .' .; ;p:' ' '■.
• Use this mode when playing sources recorded with Dolby Digital.
•There are no special steps required to playback Dolby Digital
DVDs. This system automatically switches to 5,1ch (6ch) input
when a 5.1ch (6ch) DVD is played.
Preparation:
If you have connected a subwoofer (not included), press and hold
(S.WOOFER] for about 2 seconds so “SUB W ON” is shown on the
display.
Playback the source (DVD).
“□□ DIGITAL” appears on the display.
To adjust the volume of each speaker El
by remote control only
•Sit in the nonnal listening position and make the adjustments with
the remote control.
• Before adjusting, disconnect the headphones and microphone (if
you can use). Audio effect and karaoke mode should be “FLAT" or
“OFF’.
Preparation; Press [DVD],
© Press (TEST] (iSHiFT]+iCH SELECTl).
A test signal is output.
The speaker outputting the test signal is displayed while the test is
running.
L: Front speaker (Left)
C: Center speaker
R: Front speaker (Right)
RS: Surround speaker (Right)
LS: Surround speaker (Left)
© Press [VOLUME (- or +)].
Set the volume to the normal listening level.
@ Press [A] or [V].
Adjust the output level.
•Adjust the output level of the front left and right speakers.
•Adjust the output level of the center and surround speakers so
they are the same apparent level as the front speakers.
A: Increases the output level
T: Decreases the output level
• Repeat step @ to adjust the level accordingly.
•To select a specific channel to make volume adjustments, press
[CH SELECT]. Each time it is pressed, the display changes to show
level adjustments for each speaker.
To stop the test signal
Press [TEST] ([SHIFT]+[CH SELECT]).
To adjust the volume of each speaker while enjoying the source
While enjoying the desired source;
© Press [CH SELECT] to select thé speaker.
Each time the button is pressed:
L^C-»R->RS->LS-»-SW
© Press [▼] or
[A]
to adjust the output level.
References
•To down mix Dolby Digital (5.1 ch) signals to 2 channels, press
[MIX 2CH] ([SHIFT]+[AUDIO]) on the remote control.
•Add audio effects to improve the surround effect.
Manufactured under license from Dolby Laboratories,
“Dolby”, “Pro Logic” and the double-D symbol are trademarks
of Dolby Laboratories.
Confidential
Unpublished Works. © 1992-1997 Dolby
Laboratories, Inc. All rights reserved.