Speaker grille cloth – Elecraft K2ATOBKIT User Manual
Page 15
![background image](/manuals/636084/15/background.png)
15
Fine-Tuning Filter Settings
You can optionally fine-tune your BFO settings
for each mode by ear or by using a computer-based
tool such as Spectrogram.
If you have the KSB2 option (SSB adapter), and
you made the recommended changes to the second
crystal filter, you may wish to fine-tune the LSB and
USB BFO settings so that the filters have the same
noise pitch.
Note: Only the SSB BFO settings for FL2, 3, and 4
should be made in receive mode. The SSB BFO
settings for FL1 should be made in transmit mode,
either listening to your signal locally or having a
nearby station listen for you. This is because FL1 is
always used in transmit mode (and for receive, when
selected), whereas FL2-4 are only used in receive
mode. FL2-4 can be set up differently without affecting
your transmitted signal. Refer to the KSB2 manual for
more details.
AF GAIN Potentiometer Test
The following two steps apply if you made the AF
GAIN potentiometer smoothness modification.
Rotate the AF GAIN control slowly, near the
counter-clockwise end of its rotation, while listening to
a steady carrier (e.g., the internally-generated signal at
4.000 MHz). There should be no noticeable noise
(crackles, etc.) as you rotate the control.
Set the AF GAIN control to its fully counter-
clockwise position (minimum gain). You should hear
complete silence, with no audio signal leak-through.
13. Speaker grille cloth
Grille cloth (part #E850089) can optionally be added to
your original K2 top cover. (The KPA100 module
already has grille cloth for its speaker.)
Remove the speaker from the top cover. This may
involve removing the battery option (KBT2) or other
top-cover options. If you do have to remove a battery,
be sure to turn the battery switch OFF using the rear-
panel slide switch. Also, disconnect both leads from
the battery terminals and cover the terminals with tape
to prevent accidental shorts.
Trim the supplied grille cloth to the size of the
speaker frame.
Place the #4 fibre washers (black) at each of the
top cover's four speaker mounting holes. Trim the
corners of the grille cloth so it just fits between the
fibre washers, not touching them.
Place the speaker on top of the fibre washers and
grille cloth. Secure it with four 3/8" (9.5 mm) screws,
#4 lock washers, and 4-40 nuts. Do not over-tighten the
nuts.
Re-install the top cover or KPA100 module.
- KX3 Owner's Manual
- KX3 Assembly Manual
- KX3 Assembly Manual Errata
- KX3-2M
- KX3-PCKT
- KX3 Mobile Installation And Operation Guide
- KX3 Guide for Blind Operators
- KX3 Quick Reference
- K3 Programmers Reference
- KX3 Speaker Grille Instructions
- KXFL3 Filter Option
- KXFL3 Filter Option Errata
- KXAT3
- KXBC3
- KXPD3
- Proset Boom Headset
- PX3 Owner's Manual
- PX3 Owners Manual Errata
- KXPA100 Manual
- KXPA100 Assembly Manual
- KXPA100 Assembly Errata
- KXPA100 Programmers Reference
- KXAT100 Installation Manual
- KX1 Manual
- KXAT1
- KXPD1
- KXB30
- KXB3080
- K1
- K1 1.09 F/W
- KNB1 Manual
- KAT1 Manual
- KFL1-2
- KTS1
- KBT1 Manual
- KBT1 Manual Errata
- K1BKLTKT LCD Mod Kit
- K2 Owner's Manual
- K2 Owner's Manual Errata
- K2 PLL
- K2ATOBKT
- K2 Keying Modification Instructions
- KPA100 Manual
- KPA100 Shield Upgrade
- KPA100MODKT
- KPA100UPKT
- KPA100UPKT Errata
- KSB2
- ProSet-K2
- K160RX
- KNB2 Manual
- KNB2 Manual Errata
- KBT2
- KAT2
- KAT100
- KIO2
- K2
- KDSP2 Manual
- KDSP2 Manual Errata
- KAF2
- K60XV Manual
- K60XV Manual Errata
- SSBCAPKT
- K2VCOSHLDKT
- 2.04 K2 Firmware
- K3 Owner's Manual
- K3 Owner's Manual Errata
- K3 Assembly Manual
- K144XV Manual
- K144XV Install & Operation Manual Errata
- K144XV Ref Lock Manual
- K144XV Ref Lock Errata
- KPA3 Manual
- KPA3 Power Connector Replacement Manual
- KAT3
- KBPF3
- KRX3
- K3EXREF
- K3EXREF Errata
- K3 Crystal Filter Manual
- KXV3 Manual
- KXV3 Option Manual Errata
- KXV3A
- KDVR3
- KTCXO3-1
- PR6
- PR10
- PR6-10 Manual
- PR6-10 Manual Errata
- K3-Remote Owner's Manual
- KAT500 Owners Manual
- KAT500 Manual Errata
- KAT500 Serial Command Reference
- KPA500 Owner's Manual
- KPA500 Kit Assembly Manual
- KPA500 Fuse Installation
- KPAK3AUX
- KPA500 Prog. Reference
- XV Transverter Owner's Manual
- XV Assembly Manual for XV50
- XV Assembly Manual for XV432 MHz
- XV 432 Assembly Manual Errata
- XV 432 Assembly Installation Instruction
- XV Bypass Capacitor Change
- T1 ATU Owner's Manual
- T1 Assembly Manual
- T1-FT817 Remote Control Cable Manual
- W1
- AF1 Audio Filter
- AF1 Audio Filter Errata
- AT1 41 dB Step Attenuator
- 2T-Gen
- BL1 (4:1)
- BL1 (1:1)
- BL2
- CP1
- DL1
- Ngen
- XG2 Manual
- XG2 Manual Errata
- XG50
- KRC2 Manual
- KRC2 Manual Errata
- KRC2ACC
- P3 High-Performance Panadapter Manual
- P3 High-Performance Panadapter Errata
- P3 SVGA Instructions
- P3 SVGA Errata
- P3 Programmer's Reference
- P3SVGA
- XG3 RF