EFCO 8750XD - Manual (Page 11)

EFCO 2012 Page 11
Series 8750XD Unitized Curtain Wall Installation Instructions
Section 2 - Package Identification
“ K ” PACKAGE IDENTIFICATION
Part Description Finish Cut Length Tooling Reference Parts used For Assembly
KV19 HANGER/LOAD CLIP MILL FM41 - 6.223 PUNCH FM41 (2) MTZO (4) M173 (4)
KV20 OPTIONAL RETRACTABLE HANGER MILL FM42 - 3.000 CUT & MILL FM42 (2) MTZO (4) M173 (4)
KV21 90 DEG OUTSIDE CORNER MULLION ANCHOR MILL FM43/17 - 8.000 CUT & DRILL FM43 (1) FM17 (1) M170 (1) M172 (3) M174 (3) M169 (1)
KV22 90 DEG INSIDE CORNER MULLION ANCHOR MILL FM44/17 - 8.000 CUT & DRILL FM44 (1) FM17 (1) M170 (1) M172 (3) M174 (3) M169 (1)
KV23 RIGHT HAND 90 DEG OUTSIDE CORNER SLAB ANCHOR MILL FM62 - 16.000 CUT & MILL FM62 (1) FM60 (2)
KV24 JAMB OR 90 DEG INSIDE CORNER SLAB ANCHOR MILL FM61 - 11.000 CUT & MILL FM61 (1) FM60 (2)
KV25 MULLION DYNAMIC LOADING CLIP MILL FM49 - 8.000 CUT FM49 (1) FM48 (1) STB1 (6)
KV26 LEFT HAND JAMB DYNAMIC LOADING CLIP MILL FM64 - 8.000 CUT FM64 (1) FM48 (1) STB1 (6)
KV27 STANDARD MULLION ANCHOR MILL FM11/17 - 8.000 CUT & DRILL FM11 (1) FM17 (1) M170 (1) M172 (3) M174 (3) M169 (1)
KV28 RIGHT HAND JAMB DYNAMIC LOADING ANCHOR MILL FM65 - 5.500 CUT FM65 (1) FM48 (1) STB1(6)
KV29 INSIDE CORNER DYNAMIC LOADING CLIP MILL FM50/51 - 8.000 CUT FM50 (1) FM51 (1) FM48 (1) STB1 (6)
KV30 OUTSIDE CORNER DYNAMIC LOADING CLIP MILL FM52/53 - 8.000 CUT
FM52 (1) FM53 (1)
FM48 (1) STB1 (6)
KV31 DYNAMIC SILL END DAM MILL FM55 - 5.188 SHEAR & PUNCH FM55 (1) STC7 (2)
KV32 STATIC SILL END DAM MILL FM56 - 4.188 SHEAR & PUNCH FM56 (1) STC7 (2)
KV34 LEFT HAND 90 DEG OUTSIDE CORNER SLAB ANCHOR MILL FM63 - 16.000 CUT & MILL FM63 (1) FM60 (2)
KV35 HIGH LOAD RIGHT HAND 90 DEG OUTSIDE CORNER SLAB ANCHOR MILL FM67 - 21.000 CUT & MILL FM67 (1) FM60 (3)
KV36 HIGH LOAD LEFT HAND 90 DEG OUTSIDE CORNER SLAB ANCHOR MILL FM68 - 21.000 CUT & MILL FM68 (1) FM60 (3)
KV37 HIGH LOAD MULLION, JAMB OR 90 DEG INSIDE CORNER SLAB ANCHOR MILL FM66 - 21.000 CUT & MILL FM66 (1) FM60 (3)
KV39 STACK SILICONE END DAM SILICONE HC13 - 5.250 HC13 (1) WO7V (4")
KV41 SUB HEAD END DAM MILL FM69 - 8.156 SHEAR & PUNCH FM69 (1) SPZ1 (2)
KV43 DOOR JAMB END CAP PER JOB FM39 - 3.000 SHEAR FM39 (1) WO7V (3")
KV46 RIGHT HAND SLAB HOOK ANCHOR MILL FM06 - 3.000 CUT & MILL FM06 (1) M171 (1)
KV47 LEFT HAND SLAB HOOK ANCHOR MILL FM05 - 3.000 CUT & MILL FM05 (1) M171 (1)
KV48 11" & 13" SUN SHADE ARM MOUNTING BRACKET MILL FM82 - 13.000 CUT & DRILL FM82 (1) S124 (5) S134 (6)
KV49 INSIDE OR OUTSIDE CORNER ALIGNMENT CLIP MILL FM78 - 4.000 CUT & MILL FM78 (1) STC7 (3)