EFCO Special Purpose Windows Installation - Manual (Page 58)

MEASURE THE INTERIOR HORIZONTAL OPENING WIDTH AND
SNAP IN PLACE.
CUT THE HORIZONTAL TRIM COVERS ACCORDINGLY, THEN
THROUGH AND MUST BE INSTALLED FIRST. TO INSTALL,
FIELD. HORIZONTAL INTERIOR TRIM COVERS ALWAYS RUN
ALL INTERIOR TRIM COVERS ARE TO BE CUT TO SIZE IN THE
3)
2)
TO SECURE THE WINDOW IN THE OPENING.
MUST BE ATTACHED TO BOTH THE WINDOW AND THE OPENING
STRUCTURAL SUPPORT FOR THE WINDOW UNIT. EACH CLIP
IN CLIPS IS NOT BY EFCO. THE TRIM CLIPS PROVIDE THE
WITH THE ERECTOR FURNISHED ANCHORS. HOLE DRILLING
WINDOW WITH EFCO’S STT6 SCREWS AND TO THE OPENING
CORNER, THEN EVERY 16" O.C.. ATTACH THE CLIPS TO THE
ATTACHING THE FIRST CLIP APPROXIMATELY 6" FROM EACH
INSTALL THE HEAD AND SILL INTERIOR TRIM CLIPS. START BY 1)
CUT THE VERTICAL TRIM COVERS TO THE PROPER LENGTH.
MEASURE BETWEEN THE HORIZONTAL TRIM COVERS, THEN
SNAP THE VERTICAL TRIM COVERS INTO PLACE.
4)
#10 PANN HEAD
OR SMALLER
STT6 #8-18 X 9/16
PL-PH-SMS ZC TEK/2
.187
2205 3"CLIP
THE ALIGNMENT TAB ON
THE JAMB TRIM CLIPS
WICKET SIZE WITH
ENSURE THE CORRECT
INSTALLING THE JAMB INTERIOR TRIM CLIPS REQUIRES A
SIMILAR METHOD OF ATTACHMENT AS NOTED IN STEP ONE.
THE EXCEPTION IS THAT THE ALIGNMENT TAB ON THE JAMB CLIPS
MUST BE TIGHT AGAINST THE WINDOW LEG TO ENSURE THE
CORRECT WICKET SIZE WITH PARALLEL TRACKS. OPENING SIZE
ADJUSTMENTS MUST BE MADE BY SHIMMING BETWEEN
THE CLIP AND THE EXISTING OPENING RATHER THAN CHANGING
THE CLIP TO WINDOW FRAME OVERLAP. (SEE FIG. BELOW)
MUST BE TIGHT AGAINST
PARALLEL TRACKS.
EXISTING OPENING
SCREEN MEETING RAIL WITH STT6 TEK SCREW. THE SHEAR
ATTACH SHEAR BLOCKS FOR MOUNTING THE HORIZONTAL
BLOCK SHOULD BE LOCATED .062 BELOW THE SCREEN TOP
5)
SCREEN TRACK ON BOTH SIDES. THE LOWER TRIM
PRESS THE LOWER TRIM FILLER VINYL INTO THE
FILLER WILL HAVE A 9/16" SLOT 1/2" DOWN FROM
7)
INTERIOR VERTICAL SLIDING SCREEN INSTALLATION
.179
.062
TOP OF THE SILL
HEIGHT OF SCREEN
WICKET FROM THE
INTERIOR TRIM
RAIL IF THE SCREEN WAS SITTING ON TOP OF THE SILL TRIM.
(SEE FIG. BELOW.)
THE JAMB TRIM. SOME FIELD ADJUSTMENTS MAY BE REQUIRED
ON THE ROOM SIDE. CARE MUST BE TAKEN NOT TO SCRATCH
WITH THE SHORTER WEATHERSTRIP AND ATTACHMENT HOLE
LOWER THE SCREEN MEETING RAIL OVER THE SHEAR BLOCKS
TO THE SCREEN MEETING RAIL LENGTH, TO FACILITATE
6)
THE WINDOW LEG TO
SHEAR BLOCK
PL-FH-SMS 18-8 AB UC
SFZ5 #8-15 x 3/8"
AND ATTACHMENT HOLE
SHORTER WEATHERSTRIP
GOES TO THE ROOM SIDE
2207 SCREEN MEETING RAIL
SHEAR BLOCK
INSTALLATION. FASTEN THE MEETING RAIL TO THE SHEAR BLOCK
WITH ONE SFZ5 SCREW IN EACH END. HOLE DRILLING IN THE
SHEAR BLOCK FOR THE SFZ5 IS NOT BY EFCO.
LB76
THE TOP END AND EVERY FOUR INCHES AFTER THAT.
LOWER
TRIM FILLER
THE SCREEN TRACK BEHIND THE UPPER END OF THE SCREEN.
INSTALL THE OTHER UPPER TRIM FILLER BY SLIDING IT INTO
AND LOWER THE SCREEN TO THE BOTTOM OF THE TRACKS.
THE EMPTY UPPER JAMB TRACK. RETRACT BOTH PLUNGERS
PLUNGERS FACING THE ROOM, SIDE LOAD THE SCREEN INTO
WITH THE SCREEN HANDLE RAIL AT THE BOTTOM AND THE
INSTALL ONLY ONE OF THE UPPER TRIM FILLERS AT THIS TIME. 9)
PRESS THE REMAINING FILLER INTO THE TRACK.
ABOUT 1/2" OF FILLER WILL GO BEHIND THE FRAME, THEN
THE BOTTOM END OF THE FILLER SHOULD REST ON
THE SILL TRIM WHEN FINISHED.
IN THE FIELD. MEASURE THE REMAINING TRACK LENGTH
THE UPPER TRIM FILLERS ARE SENT LONG TO BE CUT TO SIZE
FROM THE TOP OF THE LOWER TRIM FILLER TO THE UNDERSIDE
OF THE HEAD TRIM, THEN CALCULATE THE FILLER CUT LENGTH
1/8" SHORTER. THE UPPER FILLER HAS ONLY ONE HOLE
8)
MUST BE TRIMMED AT THE OPPOSITE END.
AT THE TOP END, ADJUSTMENTS TO ITS OVER ALL LENGTH
THIS SHEET IS FOR GENERAL RECOMMENDED ERECTION
THE DETAILS ON THE SHOP DRAWINGS (IF APPLICABLE).
PROCEDURES ONLY. FOR ACTUAL JOB CONDITIONS, SEE
SCRN page 7 of 7
PH: 1-800-221-4169 FAX: 417-235-7313
EFCO CORPORATION 1000 COUNTY ROAD MONETT, MO. 65708-0609