Great Plains 3S-4010HDF Operator Manual User Manual
Operator manual, Manufacturing, inc
This manual is related to the following products:
Table of contents
Document Outline
- Operator Manual
- Important Safety Information
- Look for Safety Symbol
- Be Aware of Signal Words
- Prepare for Emergencies
- Be Familiar with Safety Decals
- Avoid High Pressure Fluids
- Use A Safety Chain
- Keep Riders Off Machinery
- Check for Overhead Lines
- Use Safety Lights and Devices
- Transport Machinery Safely
- Wear Protective Equipment
- Handle Chemicals Properly
- Shutdown and Storage
- Practice Safe Maintenance
- Tire Safety
- Safety At All Times
- Safety Reflectors and Decals
- Red Reflectors 838-266C
- Amber Reflectors 838-265C
- Daytime Reflectors 838-267C
- Danger: Cannot Read English 818-557C
- Danger: Pinch/Crush Hazard 818-590C
- Warning: Pinch/Crush Hazard 818-045C
- Warning: Excessive Speed Hazard 818-188C
- Warning: High Pressure Fluid 818-339C
- Warning Marker Pinch Point (Option) 818-579C
- Warning Overhead Marker (Option) 818-580C
- Warning: Falling Hazard 838-102C
- Caution: Tires Not A Step 818-398C
- Caution: General 818-587C
- Caution: 85 PSI Tire Pressure 848-147C
- Introduction
- Preparation and Setup
- Operating Instructions
- Adjustments
- Planting Depth
- Opener Frame Height
- Frame-Mounted Coulters
- Frame Height without Frame- Mounted Coulters
- Frame Weights
- Material Rate Setting
- 10HD Series Row Unit Adjustments
- Marker Adjustments
- Troubleshooting
- General Troubleshooting
- Planting too much
- Planting too little
- Excessive seed cracking
- No Seed Flow
- Uneven seed spacing
- Drill boxes do not empty evenly
- Openers drill too deep (bulldozing)
- Uneven seed depth
- Opener disks not turning freely
- Meter flutes locked up or shaft twisted
- Press wheels not compacting the soil as desired
- Press wheel or openers plugging
- Marker Malfunction
- Marker disk does not mark
- Drill does not fold or unfold fully
- Drill hunts in transport
- Acremeter Inaccurate
- Chain fouling
- Clutch Troubleshooting
- General Troubleshooting
- Maintenance and Lubrication
- Materials Clean-Out
- Seed Flap Replacement (s/n B1010B-)
- Seed Flap Replacement (s/n B1011B+)
- Chain Maintenance
- Bleeding Hydraulics
- Adjusting Fold Cylinders
- Leveling Drill
- Tongue Spacer Block
- Height Switch
- Detent and Pressure Plate Adjust
- Marker Maintenance
- Lubrication
- Rear Axle Beam Pivot
- Rear Caster Wheel Pivot
- Caster Detent
- Wing Caster Wheel Pivot Lock
- Wing Caster Wheel Pivot
- Gauge Wheel Assembly Pivot
- Wing Frame Vertical Pivots
- Parallel Arm Pivots
- Wing Flex Pivots
- Rockshaft
- Parallel Arm Lift Cylinder Pins
- Grease Bank
- Marker(s) (Option)
- Fertilizer Shaft Bearings (3S4010HDF only)
- Small Seeds Shaft Bearing (Option)
- Felt Barrier Seals (3S-4010HDF only)
- Seed Cup Drive Shaft Sprocket
- Drive Chains
- Rear Caster Pressure Plate Pin
- Frame-Mounted Coulter Hubs (Option)
- Marker Disk Bearings (Option)
- Main Wheel Bearings
- Options
- Appendix A - Reference Information
- Appendix B - Initial Setup
- Index