Powers 450-900 HydroPanel II Shower System with Biltmore 900 Pressure Balancing Valve - Manual (Page 4)

TI450-900 Page 4
TROUBLESHOOTING, CONTINUED
2) Turn off supply water and access the valve.
3) Check that the adjustment stem faces the correct direction for
valve operation: Refer to Figure 6.
• For NORMAL operation, Hot Inlet is on the left and Cold Inlet
is on the right. With the valve in shut off position, the flats on
the stem face the top and bottom outlets, and TOP stamped
on stem faces shower outlet.
• For REVERSE valve operation, Cold Inlet is on the right and
Hot Inlet is on the left. With the valve in shut off position, the
flats on the stem face the top and bottom outlets, and TOP
stamped on stem faces DOWN.
4) Remove handle. Remove limit stop and bonnet.Turn the stem
180° so the word TOP faces the appropriate direction.
Replace bonnet and limit stop.
6) Replace handle. Test the system. Replace shroud, sleeve,
and valve handle.
HOT INLET
SHOWER OUTLET
COLD INLET
PLUGGED
TUB OUTLET
For normal operation,
the flats of the handle
stem must face the water
outlets and
TOP must face
shower outlet.
Figure 6.
4
5
6
7
8
9
10
11
12
13
15
16
17
24
25
6
5
1
32
# Part # Description Qty Material
1 N/A Shroud 1 St Steel
4 450 268 Soap Dish 1 St Steel
5 4504011 End Cap Kit 1 Chrm Plt ABS
6 450 273 Screw 10-32 x 3/8 (shrouding) 7 St Steel
NS 141 318 Handshower with 24” Glidebar 1 -
7 450 276 Set Screw 10-32 x 7/8 1 St Steel
8 141 816 Fixed Showerhead 1 Chrm Plt Brass
9 141 379 Swivel Showerhead 1 Chrm Plt Brass
10 450 277 Gasket, Showerhead Base 1 Garlock 3000
11 450267G Showerhead Base 1 Chrm Plt Brass
12 047 013 Quad Ring 3/8 x 1/2 x 1/16 1 Buna N
13 450 274 Screw 10-32 x 1/4 (showerhead) 3 Brass
15 450 271 Screw 8-32 x 1/2 (valve handle) 1 St Steel
16 900 036 Handle Lever Kit 1 Chrm Plt Znc
17 800015H Sleeve 1 Chrm Plt Brass
17A 084 041 O-Ring 1 Buna-A
24 450 272 Screw 8-32 x 2-1/4 (dial insert) 2 St Steel
25 450 270 Insert Dial 1 Al w/Mylar
32 N/A Hydroguard /Piping Assembly 1 -
NS 089 003 3/32” Service Wrench 1 Steel
NS 089 004 1/8” Service Wrench 1 Steel
NS = Not shown in diagram NA = Not available as commercial part
Exploded View Diagram of Hydropanel II
Series 4504000 Shower Unit.
TI450-900 0632 EDP# 6508980
© 2006 Powers
USA: Phone: 1.800.669.5430 • Fax 1.847. 229 . 0526 • www.powerscontrols.com
Canada: Phone: 1.888.208.8927 • Fax 1. 888. 882 .1979 • www.powerscontrols.ca
ORDERING