Steriflow Mark 95 Series - Manual (Page 6)

Model
95 Standard
95FT Flow-Through
Size
050 1/2" (DN15)
075 3/4" (DN20)
100 1" (DN25)
150 1-1/2" (DN40)
200 2" (DN50)
300 3" (DN80)
Body Material
6L 316L
M
ark
95 S
erieS
S
anitary
B
ack
P
reSSure
r
egulatorS
o
rDering
s
chematic
95/0514/AB
1 & 2 Body
Finish Cvs (Kvs)
A 20Ra Interior/63rms Exterior (Std) A 0.5 & 1.5 (0,5 & 1,3)
B 20Ra Interior/20Ra Exterior G 3.0 (2,6)
C 8Ra Interior/63rms Exterior* H 4.5 (3,9)
D 20Ra Interior/8Ra Exterior K 5.5 (4,7)
E 8Ra Interior/8Ra Exterior* M 10.0 (8,6)
F 8Ra Interior/20Ra Exterior* N 19.0 (16,3)
P 28.0 (24,1)
* Handle and all external surfaces meet spec per above. The adjust-
ing screw is a threaded part and cannot be polished beyond 20Ra
Note: These valves are all tri-clamp end connections. Consult factory
for other options.
— — —
1
1 & 2 3 & 4 5 & 6 7 & 8 9 & 10 11 & 12 13 & 14
3 Trim Finish
A 20Ra (Standard)
B 8Ra
4 Trim – Cv (Kv) & Seat
5 0.5 (0,4) Hard Seat N 5.5 (4,7) Jorlon Seat
A 1.5 (1,3) Hard Seat P 10 (8,6) Hard Seat
E 3.0 (2,6) Hard Seat Q 10 (8,6) Teflon Seat
F 3.0 (2,6) Teflon Seat R 10 (8,6) Jorlon Seat
G 3.0 (2,6) Jorlon Seat S 19 (16,3) Hard Seat
H 4.5 (3,9) Hard Seat T 19 (16,3) Teflon Seat
J 4.5 (3,9) Teflon Seat U 19 (16,3) Jorlon Seat
K 4.5 (3,9) Jorlon Seat V 28 (24.1) Hard Seat
L 5.5 (4,7) Hard Seat W 28 (24,1) Teflon Seat
M 5.5 (4,7) Teflon Seat X 28 (24,1) Jorlon Seat
5 & 6 O-Ring/Diaphragm
Cv 0.5 thru 3.0
BS Buna/SST Dia.
EL EPDM/EPDM Dia.
ES EPDM/SST Dia.
SS Silicone/SST Dia.
TL Teflon Encap. Silicone/SST Dia. (1-1/2" - 3")
TG Teflon Encap. Viton/Jorlon Dia.
TE Teflon Encap. Viton/SST Dia.
VS Viton/SST Dia.
ZZ Non-standard
8 Range PSI (Bar)
A 3 - 8 (0,2 - 0,6)*
B 3 - 25 (0,3 - 1,7)*
D 5 - 30 (0,3 - 2,1)
E 10 - 25 (0,7 - 1,7)
F 5 - 25 (0,3 - 1,7)/Elas. Diaphragm
P 15 - 25 (1,0 - 1,7)
G 15 - 40 (1,0 - 2,8)
H 15 - 50 (1,0 - 3,4)
J 15 - 60 (1,0 - 4,1)
K 35 - 85 (2,4 - 5,9)
L 35 - 90 (2,4 - 6,2)
Q 50 - 105 (3,4 - 7,2)
7 Adjusting Screw Finish (Except Threads)
A Electro-polished (Standard)
B 20Ra (SFV5)
C 8Ra
9 & 10 Diaphragm
6L SST (all exterior)
EP EPDM (all exterior)
JL Jorlon (all exterior)
UJ Ultra-thin Jorlon (all exterior)
11 & 12 Actuator Finish/Type
AA Standard
BA 20Ra (SFV5) exterior
CA 8Ra exterior
DA Electro-polished for 2" & 3"
5 & 6 O-Ring/Diaphragm
Cv > 3.0
BU Buna/SST Dia.
EE EPDM/EPDM Dia.
EP EPDM/SST Dia.
SL Silicone/SST Dia.
TS Teflon Encap. Silicone/SST Dia. (1-1/2" - 3")
TY Teflon Encap. Viton/Jorlon Dia.
TV Teflon Encap. Viton/SST Dia.
VT Viton/SST Dia.
ZZ Non-standard
13 & 14 PED Compliance
00 Not Required
0G SEP/PED Compliant
* Must use EPDM or Ultra-thin Jorlon diaphragm
Body Configuration
Leave blank for standard
90 3/4" Tri-Clamp F/Gauge @ 90°
180 3/4" Tri-Clamp F/Gauge @ 180°
270 3/4" Tri-Clamp F/Gauge @ 270°