SawStop CNS175-AU - Manual (Page 17)

SawStop 10” Contractor Saw 15
Unpacking Your Saw
miter gauge
blade guard
assembly
riving
knife
blade wrenches
(two)
assembly instructions poster hardware pack #1
elevation handwheel
package
tilt handwheel
package
owner’s manual
hardware pack #2
motor belt guard motor belt
OWNER’S MANUAL
10” CONTRACTOR SAW
SawStop ®
Assembling Your SawStop Contractor Saw
SawStop Service Department 503-582-9934
www.sawstop.com
Before assembling your saw, make sure that you have all the components identified on pages 12 and 13 in the Owner’s Manual, including hardware pack #1 and hardware pack #2. Call the SawStop Service Department at 503-582-9934 if any components are missing. Hardware pack #2 includes some of the tools needed to assemble the saw. You will also need the following additional tools:
1. an 8 mm socket 2. a 10 mm wrench 3. two 13 mm wrenches 4. a level or straight edge
Assembling the Stand
1
• Locate the stand components labeled through and hardware pack #1. All of the hardware needed to assemble the stand is located in the area with the blue background on hardware pack #1. In order to easily identify the hardware used in each of the following steps, the different pieces of hardware are numbered on the hardware pack and on these assembly instructions.
A F
2
• Assemble the front of the stand by attaching two of the legs marked to the front panel marked . Make sure that the legs are in front of the front panel. Bumps on the legs fit into holes in the front panel to align the legs. Attach the legs to the front panel using four M8 x 20 carriage bolts , four M8 washers , four M8 lock washers , and four M8 hex nuts . Do not fully tighten the nuts at this time. Leaving the nuts loose will make it easier to align holes as you assemble the rest of the stand.
4 3 2
1 A
B
A B
1 2 3 4
A
3
4 3 2
1
• Assemble the rear of the stand by attaching the remaining two legs marked to the rear panel marked . Make sure that the legs are in front of the rear panel. Bumps on the legs fit into holes in the rear panel to align the legs. Attach the legs to the rear panel using four M8 x 20 carriage bolts , four M8 washers , four M8 lock washers , and four M8 hex nuts . Do not fully tighten the nuts at this time.
A C
A
C
A
1 2 3 4
4
• Attach one of the side panels marked between the front and rear portions of the stand. Make sure the legs are in front of the side panel and that the side panel is under the top flanges of the front and rear panels. Bumps on the legs fit into holes in the side panel to align the legs. Use four M8 x 20 carriage bolts , four M8 washers , four M8 lock washers , and four M8 hex nuts to attach the side panel to the front and rear portions. Do not fully tighten the nuts.
4 3 2 1
D
D
1 2 3 4
5
• Repeat the prior step to attach the remaining side panel marked to the opposite side of the stand.
1 2 3 4
D
D
6
• Attach one long bracket marked between the legs on the right side of the stand. Make sure the legs are in front of the brackets. Use two M8 x 20 carriage bolts , two M8 washers , two M8 lock washers , and two M8 hex nuts to attach the long bracket. Do not fully tighten the nuts. Repeat this process to attach the remaining long bracket between the legs on the left side of the stand.
1 2 3 4
7
F
4 3 2 1
F 8
• The front, rear and side panels have flanges that overlap to define mounting holes through which you will bolt the saw to the stand. There is one hole in each corner of the stand. Adjust the panels until the holes align and then tighten all of the nuts in the stand using a 13 mm wrench.
9
4
2
2
4
5
• Attach a foot to the bottom of each leg by threading an M8 hex nut on each foot and then placing an M8 washer over the nut. Insert a foot into the hole at the base of each leg and then place a second M8 washer and thread a second M8 hex nut onto each foot. Do not fully tighten the nuts. The stand is now fully assembled.
Note: If you purchased an optional mobile base for your saw, install it now by following the instructions that came with the mobile base.
4 2
2 4
5 Mounting the Saw
to the Stand
10 • Remove the saw from the box and locate the mounting hardware. All of the hardware needed to mount the saw to the stand is located in the area with the yellow background on hardware pack #1.
11
• With the help of an assistant, pick up the saw and carefully set it on the assembled stand with the front of the saw above the front panel of the stand. Align the mounting holes in the bottom corners of the saw with the mounting holes in the top corners of the stand. While moving the saw do not set it down in the upright position on a solid surface because the dust shroud can be damaged. Warning! The saw weighs approximately 140 pounds. Be careful and use proper lifting technique to avoid injury.
• Attach one of the short brackets marked between the two front legs. Make sure the legs are in front of the bracket. Use two M8 x 20 carriage bolts , two M8 washers , two M8 lock washers , and two M8 hex nuts . Do not fully tighten the nuts. Repeat this process to attach the remaining short bracket between the rear legs.
E 1 2 3 4
1 2 4 3
E
E mounting holes
0 15 30 45 SawStop 10”Contractor Saw 0 15 30 45 SawStop 10”ContractorS aw
Mounting the Saw to the Stand
Washers, M8 (32 + 2 extra) Lock Washers, M8
(24 + 2 extra)
Assembling the Stand Hex Nuts, M8 (32 + 2 extra)
Leveling Feet (4)
Hardware for Steps 10-14
Hardware for Steps 1-9 Carriage Bolts, M8 x 20 (24 + 2 extra) 1
2
4
5 3
Hex Screws, M8 x 20 (4) 6 Lock Washers, M8 (4) 8 Hex Nuts, M8 (4) 9 Washers, M8 (8) 7
Hardware Pack #1
Mounting the Saw to the Stand
Washers, M8 (32 + 2 extra) Lock Washers, M8
(24 + 2 extra)
Assembling the Stand Hex Nuts, M8 (32 + 2 extra)
Leveling Feet (4)
Hardware for Steps 10-14
Hardware for Steps 1-9 Carriage Bolts, M8 x 20 (24 + 2 extra) 1 2
4
5 3
Hex Screws, M8 x 20 (4) 6 Lock Washers, M8 (4) 8 Hex Nuts, M8 (4) 9 Washers, M8 (8) 7
Hardware Pack #1
F
Flip to
Other Side
© SawStop, LLC
Mounting the Saw to the Stand
Washers, M8 (32 + 2 extra)
Lock Washers, M8 (24 + 2 extra)
Assembling the Stand
Hex Nuts, M8 (32 + 2 extra)
Leveling Feet (4)
Hardware for Steps 10-14
Hardware for Steps 1-9
Carriage Bolts, M8 x 20 (24 + 2 extra) 1
2
4
5
3
Hex Screws, M8 x 20 (4) 6
Lock Washers, M8 (4) 8
Hex Nuts, M8 (4) 9
Washers, M8 (8) 7
Hardware Pack # 1
Tools
Hex Key, M3 (1)
Hex Key, M5 (1)
Hex Key, M8 (1)
Mounting the Switch Box
Hardware for Step 22 Switch Box Keys (2) Washers, M6 (2) 14 Hex Screws, M6 x 20 (2) 15
Installing the Motor and Belt Guard
Hardware for Steps 17-19 Washers, M5 (4) 10 Hex Nuts, M5 (4) 11
Mounting the Extension Wings
Hardware for Steps 20-21
Lock Washers, M8 (8) 12 Hex Screws, M8 x 16 (8) 13
Hardware Pack # 2
Blade Spacing Adjustment Gauge (1)