Horner APG ZX 752 OCS HE-ZX1152 User Manual
Page 5
MAN0960-03-EN
Specifications / Installation
__________________________________________________________________________________________________________________________________________________________________________
11/30/2011 #1037
5
Port and Connector Pin-outs
5.1
CAN Network Port and Wiring
6 Pin dual CAN connector
CAN 1 Port Pin Assignments
Pin
Signal
Signal Description
Direction
1
#1 V-
CAN #1 Ground - Black
−
2
#1 CN_L
CAN #1 Data Low - Blue
In/Out
3
#1 CN_H
CAN #1 Data High-White
In/Out
CAN 2 Port Pin Assignments
4
#2 V-
CAN #2 Ground - Black
-
5
#2 CN_L
CAN #2 Data Low - Blue
In/Out
6
#3 CN_H
CAN #2 Data High-White
In/Out
5 Pin CAN connector for Adapter Board
NET Port Pin Assignments
Pin
Signal
Signal Description
Direction
1
V-
CAN Ground - Black
−
2
CN_L
CAN Data Low - Blue
In/Out
3
SHLD
Shield Ground - None
−
4
CN_H
CAN Data High - White
In/Out
5
V+ (NC)
No Connect - Red
−
5.2
Power Port and Wiring
5.3
Ethernet Port
Speeds
10 BaseT Ethernet (10-Mbps)
100 BaseTx Fast Ethernet (100-Mbps)
1000 Base Tx Fast Ethernet (1000-Mbps)
Modes
Half or Full Duplex
Auto-Negotiation
10/100/1000-Mbps and Half/Full Duplex
Connector Type
Shielded RJ-45
Cable Type
(Recommended)
CAT5 (or better) UTP
Port
Auto MDI/MDI-X
5.4
Serial Ports 1, 2 and 3
Serial Port 1&3 Pin Assignments RS-232
Pin
Signal
Signal Description
Direction
1
CD
Carrier Detect
2
RX
Receive
IN
3
TX
Transmit
OUT
4
DTR
Data Terminal Ready
5
GND
Ground
-
6
DSR
Data Set Ready
7
RTS
Ready to Send
8
CTS
Clear to Send
9
RI
Ring Indicate
Serial Port 2 Pin Assignments RS-485
Pin
Signal
Signal Description
Direction
1
TX/RX -
Receive/Transmit -
In/Out
2
TX/RX +
Receive/Transmit +
In/Out
3
NC
Do Not Connect
-
4
NC
Do Not Connect
-
5
GND
Ground
-
6
DSR
Data Set Ready
7
RTS
Ready to Send
8
CTS
Clear to Send
9
RI
Ring Indicate
5.5
VGA Port
The VGA port allows the items displayed on the internal display to be mirrored to an
external display or projects. The connector uses standard analog VGA signaling and
should work with a variety of monitors, displays and projects. The external display should
support the native resolution of the ZX unit.
5.6
USB Ports
The ZX units have two (ZX351) or four (ZX751 & ZX1151) standard USB ports supporting
high speed USB 2.0. These ports will support external drives for data storage such as
data logging, screen captures, program loading… Drives larger than 2 gigabytes are
supported and should be formatted with FAT-32. Future firmware updates will allow
other peripherals to be connected to these ports
6
Technical Support
For assistance and manual updates, contact Technical Support at the
following locations:
North America:
Tel: 317 916-4274
Fax: 317 639-4279
Web:
http://www.heapg.com
Email:
Europe:
Tel: +353-21-4321266
Fax: +353-21-4321826
Web:
http://www.horner-apg.com
Email:
Pin
Signal
Description
1
Ground
Frame Ground
2
V-
Input Power Supply Ground
3
V+
Input Power Supply Voltage
CAN Connector
Use the CAN Connector when
using CsCAN network.
Torque rating 4.5 – 7 Lb-In
(0.50 – 0.78 N-m)
Power Connector
Power Up:
Connect to Earth Ground.
Apply 10 - 30 VDC.
Screen lights up with slight delay.
Torque rating 4.5 – 7 Lb-In
(0.50 – 0.78 N-m)
1
6
1
6