B.71 [source:]voltage:mode command, B.72 [source:]voltage:mode? query, B.73 [source:]voltage:protection:over command – KEPCO EL Series Electronic Load Operator Manual P/N 243-1295 Firmware Version 1.232 (Unit Rev 0 or 1) User Manual

Page 71: B.74 [source:]voltage:protection:over? query, B.77 [source:]voltage:protection:under command, B.78 [source:]voltage:protection:under? query, B.71, Source, B.72, B.73

SERIES EL 063010

B-11

B.71 [SOURce:]VOLTage:MODE COMMAND

VOLT:MODE

Syntax:

Short Form: [SOUR:]VOLT:MODE

Long Form: [SOURce:]VOLTage:MODE

Description: Selects voltage mode.

B.72 [SOURce:]VOLTage:MODE? QUERY

VOLT:MODE?

Syntax:

Short Form: [SOUR:]VOLT:MODE?

Long Form: [SOURce:]VOLTage:MODE?

Returns: = CURR, POW, VOLT, RES, COND, OFF

Description: Returns the present mode: CURRent, POWer, VOLTage, RESistance, CONDuctance, OFF

B.73 [SOURce:]VOLTage:PROTection:OVEr COMMAND

VOLT:PROT:OVE

Syntax:

Short Form: [SOUR:]VOLT:PROT:OVE
Long Form: [SOURce:]VOLTage:PROTection:OVEr
where = overvoltage protection limit

Description: Sets overvoltage protection limit. Overvoltage protection setpoint is stored in non-volatile memory;

value is restored upon power-up.

B.74 [SOURce:]VOLTage:PROTection:OVEr? QUERY

VOLT:PROT:OVE?

Syntax:

Short Form: [SOUR:]VOLT:PROT:OVE?
Long Form: [SOURce:]VOLTage:PROTection:OVEr?
Returns = overvoltage protection limit

Description: Indicates overvoltage protection limit.

B.75 [SOURce:]VOLTage:PROTection:OVEr:STATe[:LEVel] COMMAND

VOLT:PROT:OVE:STAT

Syntax:

Short Form: [SOUR:]VOLT:PROT:OVE:STAT[:LEV]
Long Form: [SOURce:]VOLTage:PROTection:OVEr:STATe[:LEVel]
where = 1 (enabled) or 0 (disabled)

Description: Enables (1) or disables (0) the overvoltage protection level set using VOLT:PROT:OVE. This

command saves having to change the protection level to some value outside of the operating range.

B.76 [SOURce:]VOLTage:PROTection:OVEr:STATe[:LEVel]? COMMAND

VOLT:PROT:OVE:STAT?

Syntax:

Short Form: [SOUR:]VOLT:PROT:OVE:STAT[:LEV]
Long Form: [SOURce:]VOLTage:PROTection:OVEr:STATe[:LEVel]
where = 1 (enabled) or 0 (disabled)

Description: Indicates whether the overvoltage protection level set using VOLT:PROT:OVE is enabled (1) or

disabled (0).

B.77 [SOURce:]VOLTage:PROTection:UNDer COMMAND

VOLT:PROT:UND

Syntax:

Short Form: [SOUR:]VOLT:PROT:UND
Long Form: [SOURce:]VOLTage:PROTection:UNDer
where = undervoltage protection limit

Description: Sets undervoltage protection limit. Undervoltage protection setpoint is stored in non-volatile mem-

ory; value is restored upon power-up.

B.78 [SOURce:]VOLTage:PROTection:UNDer? QUERY

VOLT:PROT:UND?

Syntax:

Short Form: [SOUR:]VOLT:PROT:UND?

Long Form: [SOURce:]VOLTage:PROTection:UNDer?

Returns: = undervoltage protection limit

Description: Indicates undervoltage protection limit.