beautypg.com

B.15 lock? query, B.16 sense:current:range command, B.17 sense:current:range? query – KEPCO EL Series Electronic Load Operator Manual P/N 243-1295 Firmware Version 1.232 (Unit Rev 0 or 1) User Manual

Page 64: B.18 sense:voltage:range command, B.19 sense:voltage:range? query, B.20 [source:]input[:state] command, B.21 [source:]input[:state]? query, B.22 [source:]input:protection:clear command, B.15, B.16

background image

B-4

SERIES EL 063010

B.15 LOCK? QUERY

LOCK?

Syntax:

Short Form: LOCK?

Long Form: LOCK?

Returns: = OFF, EMERgency or LOCKed

Description: Indicates state of front panel controls.

B.16 SENSe:CURRent:RANGe COMMAND

SENS:CURR:RANG

Syntax:

Short Form: SENS:CURR:RANG Long Form: SENSe:CURRent:RANGe
Where: = 0, 1, 2, 3 or 4

Description: Controls the placement of the decimal point during remote interface readback of current and

on the front panel AMPS display.
Display Ranges: 0 - Auto, 1 - 0.000, 2 - 00.00, 3 - 000.0, 4 - 0000.

B.17 SENSe:CURRent:RANGe? QUERY

SENS:CURR:RANG?

Syntax:

Short Form: SENS:CURR:RANG?

Long Form: SENSe:CURRent:RANGe?

Returns: = 0, 1, 2, 3 or 4

Description: Indicates the placement of the decimal point during remote interface readback of current and

on the front panel AMPS display.
Display Ranges: 0 - Auto, 1 - 0.000, 2 - 00.00, 3 - 000.0, 4 - 0000.

B.18 SENSe:VOLTage:RANGe COMMAND

SENS:VOLT:RANG

Syntax:

Short Form: SENS:VOLT:RANG

Long Form: SENSe:VOLTage:RANGe

Where: = 0, 1, 2, 3 or 4

Description: Controls the placement of the decimal point during remote interface readback of voltage, and

on the front panel VOLTS display.
Display Ranges: 0 - Auto, 1 - 0.000, 2 - 00.00, 3 - 000.0, 4 - 0000.

B.19 SENSe:VOLTage:RANGe? QUERY

SENS:VOLT:RANG?

Syntax:

Short Form: SENS:VOLT:RANG? Long

Form:

SENSe:VOLTage:RANGe?

Returns: = 0, 1, 2, 3 or 4

Description: Indicates the placement of the decimal point during remote interface readback of voltage, and

on the front panel VOLTS display.
Display Ranges: 0 - Auto, 1 - 0.000, 2 - 00.00, 3 - 000.0, 4 - 0000.

B.20 [SOURce:]INPut[:STATe] COMMAND

INP

Syntax:

Short Form: [SOUR:]INP[:STAT]

Long Form: [SOURce:]INPut[:STATe]

where = 0 or OFF (load disengaged) or 1 or ON (load engaged)

Description: Used to engage or disengage the load from the UUT. When set to 1 the load engages at the pro-

grammed mode and corresponding setpoint value; when set to 0 the load disengages.

B.21 [SOURce:]INPut[:STATe]? QUERY

INP?

Syntax:

Short Form: [SOUR:]INP[:STAT]?

Long Form: [SOURce:]INPut[:STATe]?

Returns = 0 or OFF (load disengaged) or 1 or ON (load engaged)

Description: Indicates whether load is engaged or disengaged from the UUT. When set to 1 the load is

engaged, when set to 0 the load is disengaged.

B.22 [SOURce:]INPut:PROTection:CLEar COMMAND

INP:PROT:CLE

Syntax:

Short Form: [SOUR:]INP:PROT:CLE

Long Form: [SOURce:]INPut:PROTection:CLEar

Description: Resets protection from overcurrent, overpower, etc.