KEPCO EL Series Electronic Load Operator Manual P/N 243-1295 Firmware Version 1.232 (Unit Rev 0 or 1) - Manual (Page 70)

B-10
SERIES EL 063010
B.63 [SOURce:]RESistance[:LEVel][:IMMediate][:AMPlitude] COMMAND
RES
Syntax: Short Form: [SOUR:]RES[:LEV][:IMM][:AMP]
Long Form: [SOURce:]RESistance[:LEVel][:IMMediate][:AMPlitude]
Where: = resistance setpoint
Description: Establishes resistance setpoint. Resistance setpoint is stored in non-volatile memory; value is
restored upon power-up.
B.64 [SOURce:]RESistance[:LEVel][:IMMediate][:AMPlitude]? QUERY
RES?
Syntax: Short Form: [SOUR:]RES[:LEV][:IMM][:AMP]?
Long Form: [SOURce:]RESistance[:LEVel][:IMMediate][:AMPlitude]?
Returns: = resistance setpoint
Description: Indicates resistance setpoint.
B.65 [SOURce:]RESistance:MODE COMMAND
RES:MODE
Syntax: Short Form: [SOUR:]RES:MODE Long Form: [SOURce:]RESistance:MODE
Description: Selects resistance mode.
B.66 [SOURce:]RESistance:MODE? QUERY
RES:MODE?
Syntax: Short Form: [SOUR:]RES:MODE? Long Form: [SOURce:]RESistance:MODE?
Returns: = CURR, POW, VOLT, RES, COND, OFF
Description: Returns the present mode: CURRent, POWer, VOLTage, RESistance, CONDuctance, OFF
B.67 [SOURce:]RESistance:RANGe COMMAND
RES:RANG
Syntax: Short Form: [SOURce:]RES:RANGe Long Form: [SOURce:]RESistance:RANGe
where: = 0, 1, 2, 3 or 4
Description: Controls the placement of the decimal point during remote interface readback of resistance,
and on the front panel KW display when showing resistance. Display Ranges: 0 - Auto, 1 - 0.000,
2 - 00.00, 3 - 000.0, 4 - 0000.
B.68 [SOURce:]RESistance:RANGe? QUERY
RES:RANG?
Syntax: Short Form: [SOURce:]RES:RANGe? Long Form: [SOURce:]RESistance:RANGe?
Returns: = 0, 1, 2, 3 or 4
Description: Indicates the placement of the decimal point during remote interface readback of resistance,
and on the front panel KW display when showing resistance. Display Ranges: 0 - Auto, 1 - 0.000,
2 - 00.00, 3 - 000.0, 4 - 0000.
B.69 [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude] COMMAND
VOLT
Syntax: Short Form: [SOUR:]VOLT[:LEV][:IMM][:AMP]
Long Form: [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude]
where: = voltage setpoint
Description: Establishes voltage setpoint. Voltage setpoint is stored in non-volatile memory; value is restored
upon power-up.
B.70 [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude]? QUERY
VOLT?
Syntax: Short Form: [SOUR:]VOLT[:LEV][:IMM][:AMP]?
Long Form: [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude]?
Returns: = voltage setpoint
Description: Indicates voltage setpoint.