B.64 [source:]power:range? query, B.67 [source:]resistance:mode command, B.68 [source:]resistance:mode? query – KEPCO EL Series Electronic Load Operator Manual P/N 243-1295 Firmware Version 3.12 (Unit Rev 2) User Manual
Page 70: B.69 [source:]resistance:range command, B.70 [source:]resistance:range? query, B.64, Source, B.65, B.66, B.67

B-10
SERIES EL 070110
B.64 [SOURce:]POWer:RANGe? QUERY
POW:RANG?
Syntax:
Short Form: [SOURce:]POW:RANGe?
Long Form: [SOURce:]POWer:RANGe?
Returns:
Description: Indicates the placement of the decimal point during remote interface readback of power, and
on the front panel KW display when showing power. Display Ranges: 0 - Auto, 1 - 0.000, 2 - 00.00,
3 - 000.0, 4 - 0000.
B.65 [SOURce:]RESistance[:LEVel][:IMMediate][:AMPlitude] COMMAND
RES
Syntax:
Short Form: [SOUR:]RES[:LEV][:IMM][:AMP]
Long Form: [SOURce:]RESistance[:LEVel][:IMMediate][:AMPlitude]
Where:
Description: Establishes resistance setpoint. Resistance setpoint is stored in non-volatile memory; value is
restored upon power-up.
B.66 [SOURce:]RESistance[:LEVel][:IMMediate][:AMPlitude]? QUERY
RES?
Syntax:
Short Form: [SOUR:]RES[:LEV][:IMM][:AMP]?
Long Form: [SOURce:]RESistance[:LEVel][:IMMediate][:AMPlitude]?
Returns:
Description: Indicates resistance setpoint.
B.67 [SOURce:]RESistance:MODE COMMAND
RES:MODE
Syntax:
Short Form: [SOUR:]RES:MODE
Long Form: [SOURce:]RESistance:MODE
Description: Selects resistance mode.
B.68 [SOURce:]RESistance:MODE? QUERY
RES:MODE?
Syntax:
Short Form: [SOUR:]RES:MODE?
Long Form: [SOURce:]RESistance:MODE?
Returns:
Description: Returns the present mode: CURRent, POWer, VOLTage, RESistance, CONDuctance, OFF
B.69 [SOURce:]RESistance:RANGe COMMAND
RES:RANG
Syntax:
Short Form: [SOURce:]RES:RANGe
Long Form: [SOURce:]RESistance:RANGe
where:
Description: Controls the placement of the decimal point during remote interface readback of resistance,
and on the front panel KW display when showing resistance. Display Ranges: 0 - Auto, 1 - 0.000,
2 - 00.00, 3 - 000.0, 4 - 0000.
B.70 [SOURce:]RESistance:RANGe? QUERY
RES:RANG?
Syntax:
Short Form: [SOURce:]RES:RANGe?
Long Form: [SOURce:]RESistance:RANGe?
Returns:
Description: Indicates the placement of the decimal point during remote interface readback of resistance,
and on the front panel KW display when showing resistance. Display Ranges: 0 - Auto, 1 - 0.000,
2 - 00.00, 3 - 000.0, 4 - 0000.
B.71 [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude] COMMAND
VOLT
Syntax:
Short Form: [SOUR:]VOLT[:LEV][:IMM][:AMP]
Long Form: [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude]
where:
Description: Establishes voltage setpoint. Voltage setpoint is stored in non-volatile memory; value is restored
upon power-up.