beautypg.com

B.40 [source:]conductance:range? query, B.43 [source:]current:mode command, B.44 [source:]current:mode? query – KEPCO EL Series Electronic Load Operator Manual P/N 243-1295 Firmware Version 3.12 (Unit Rev 2) User Manual

Page 67: B.45 [source:]current:protection[:level] command, B.46 [source:]current:protection[:level]? query, B.47 [source:]current:protection:state command, B.40, Source, B.41, B.42

background image

SERIES EL 070110

B-7

B.40 [SOURce:]CONDuctance:RANGe? QUERY

COND:RANG?

Syntax:

Short Form: [SOUR:]COND:RANG?

Long Form: [SOURce:]CONDuctance:RANGe?

Returns = 0, 1, 2, 3, or 4

Description: Indicates the placement of the decimal point during remote interface readback of conductance,

and on the front panel KW display when showing conductance.
Display Ranges: 0 - Auto, 1 - 0.000, 2 - 00.00, 3 - 000.0, 4 - 0000.

B.41 [SOURce:]CURRent[:LEVel][:IMMediate][:AMPlitude] COMMAND

CURR

Syntax:

Short Form: [SOUR:]CURR[:LEV][:IMM][:AMP]
Long Form: [SOURce:]CURRent[:LEVel][:IMMediate][:AMPlitude]
Where = current setpoint

Description: Current Setting. Current setpoint is stored in non-volatile memory; value is restored upon power-up.

B.42 [SOURce:]CURRent[:LEVel][:IMMediate][:AMPlitude]? QUERY

CURR?

Syntax:

Short Form: [SOUR:]CURR[:LEV][:IMM][:AMP]?
Long Form: [SOURce:]CURRent[:LEVel][:IMMediate][:AMPlitude]?
Returns = current setpoint

Description: Indicates Current Setpoint.

B.43 [SOURce:]CURRent:MODE COMMAND

CURR:MODE

Syntax:

Short Form: [SOUR:]CURR:MODE

Long Form: [SOURce:]CURRent:MODE

Description: Selects current mode.

B.44 [SOURce:]CURRent:MODE? QUERY

CURR:MODE?

Syntax:

Short Form: [SOUR:]CURR:MODE?

Long Form: [SOURce:]CURRent:MODE?

Returns: = CURR, POW, VOLT, RES, COND, OFF

Description: Returns the present mode: CURRent, POWer, VOLTage, RESistance, CONDuctance, OFF

B.45 [SOURce:]CURRent:PROTection[:LEVel] COMMAND

CURR:PROT

Syntax:

Short Form: [SOUR:]CURR:PROT[:LEV]
Long Form: [SOURce:]CURRent:PROTection[:LEVel]
where: = current protection setpoint

Description: Establishes current protection setpoint. Current protection setpoint is stored in non-volatile mem-

ory; value is restored upon power-up. This is a user-defined value which, if exceeded during opera-
tion, causes a FAULT condition, forcing the load to disengage.

B.46 [SOURce:]CURRent:PROTection[:LEVel]? QUERY

CURR:PROT?

Syntax:

Short Form: [SOUR:]CURR:PROT[:LEV]?
Long Form: [SOURce:]CURRent:PROTection[:LEVel]?
Returns: = current protection setpoint

Description: Indicates current protection setpoint.

B.47 [SOURce:]CURRent:PROTection:STATe COMMAND

CURR:PROT:STAT

Syntax:

Short Form: [SOUR:]CURR:PROT:STAT
Long Form: [SOURce:]CURRent:PROTection:STATe
where = 1 (enabled) or 0 (disabled)

Description: Enables (1) or disables (0) the current protection level set using CURR:PROT. This command

saves having to change the protection level to some value outside of the operating range.