beautypg.com

B.57 [source:]power:mode command, B.58 [source:]power:mode? query, B.59 [source:]power:protection command – KEPCO EL Series Electronic Load Operator Manual P/N 243-1295 Firmware Version 3.12 (Unit Rev 2) User Manual

Page 69: B.60 [source:]power:protection? query, B.63 [source:]power:range command, B.56, Source, B.57, B.58, B.59

background image

SERIES EL 070110

B-9

B.56 [SOURce:]POWer[:LEVel][:IMMediate][:AMPlitude]? QUERY

POW?

Syntax:

Short Form: [SOUR:]POW[:LEV][:IMM][:AMP]?
Long Form: [SOURce:]POWer[:LEVel][:IMMediate][:AMPlitude]?
Returns = power setpoint

Description: Indicates power setpoint.

B.57 [SOURce:]POWer:MODE COMMAND

POW:MODE

Syntax:

Short Form: [SOUR:]POW:MODE

Long Form: [SOURce:]POWer:MODE

Description: Selects power mode.

B.58 [SOURce:]POWer:MODE? QUERY

POW:MODE?

Syntax:

Short Form: [SOUR:]POW:MODE?

Long Form: [SOURce:]POWer:MODE?

Returns: = CURR, POW, VOLT, RES, COND, OFF

Description: Returns the present mode: CURRent, POWer, VOLTage, RESistance, CONDuctance, OFF

B.59 [SOURce:]POWer:PROTection COMMAND

POW:PROT

Syntax:

Short Form: [SOUR:]POW:PROT

Long Form: [SOURce:]POWer:PROTection

where = power protection setpoint

Description: Selects power protection setpoint. This is a user-defined value which, if exceeded during operation,

causes a FAULT condition, forcing the load to disengage.

B.60 [SOURce:]POWer:PROTection? QUERY

POW:PROT?

Syntax:

Short Form: [SOUR:]POW:PROT?

Long Form: [SOURce:]POWer:PROTection?

Returns = power protection setpoint

Description: Indicates power protection setpoint.

B.61 [SOURce:]POWer:PROTection:STATe[:LEVel] COMMAND

POW:PROT:STAT

Syntax:

Short Form: [SOUR:]POW:PROT:STAT[:LEV]
Long Form: [SOURce:]POWer:PROTection:STATe[:LEVel]
where: = 1 (enabled) or 0 (disabled)

Description: Clears or sets power protection trip.

B.62 [SOURce:]POWer:PROTection:STATe[:LEVel]? QUERY

POW:PROT:STAT?

Syntax:

Short Form: [SOUR:]POW:PROT:STAT[:LEV]?
Long Form: [SOURce:]POWer:PROTection:STATe[:LEVel]?
where: = 1 (enabled) or 0 (disabled)

Description: Indicates whether the power protection level set using POW:PROT is enabled (1) or disabled

(0).

B.63 [SOURce:]POWer:RANGe COMMAND

POW:RANG

Syntax:

Short Form: [SOURce:]POW:RANGe

Long Form: [SOURce:]POWer:RANGe

where: = 0, 1, 2, 3 or 4

Description: Controls the placement of the decimal point during remote interface readback of power, and on

the front panel KW display when showing power. Display Ranges: 0 - Auto, 1 - 0.000, 2 - 00.00, 3
- 000.0, 4 - 0000.