17) color: black 18) italics: off – AMT Datasouth ACCEL-6300 User Manual
Page 89
User's Guide
4-26 Control Panel
Set Character Cell Size
CELL lets you specify how much to expand or compress characters so
that they look good when printed at the selected pitch. You can select
the same settings as for PITCH; that is, 10, 12, 13.3, 15, 17.1, 20 or
PS (proportional spacing). To select a setting, consider the following:
9
9
9
9
9 Using the same setting for CELL and PITCH yields the
best results.
9
9
9
9
9 Using a lower setting for CELL than for PITCH can result in
characters that overlap.
9
9
9
9
9 Using a higher setting for CELL than for PITCH can result in
wide gaps between characters.
Set Number of Lines Per Inch
LPI lets you specify how many lines to print per inch. You can select
2, 3, 4, 5, 6, 8, 9, 10 or 12 lines per inch. If the current setting is
Other, then your software application has set the number of lines per inch
to some nonstandard value.
Set Color
COLOR lets you specify a color for printing. You can select Black,
Cyan (light blue), Mgnta (magenta), Yellw (yellow), Violt (violet),
Green or Orang (orange). If a monochrome ribbon is installed, the
printer ignores your color selection.
Turn Italic Mode On and Off
ITALICS lets you turn the italic mode on and off. In the italic mode,
characters slant to the right by about 20%. You can select On or Off.
15) CELL:
10
16) LPI:
10
ABCDEFGHIJKLMN
ABCDEFGHIJKLMN
ABCDEFGHIJKLMN
ABCDEFGHIJKLMN
ABCDEFGHIJKLMN
ABCDEFGHIJKLMN
ABCDEFGHIJKLMN
ABCDEFGHIJKLMN
17) COLOR: Black
18) ITALICS: Off
User's Guide
4-26 Control Panel
Set Character Cell Size
CELL lets you specify how much to expand or compress characters so
that they look good when printed at the selected pitch. You can select
the same settings as for PITCH; that is, 10, 12, 13.3, 15, 17.1, 20 or
PS (proportional spacing). To select a setting, consider the following:
9
9
9
9
9 Using the same setting for CELL and PITCH yields the
best results.
9
9
9
9
9 Using a lower setting for CELL than for PITCH can result in
characters that overlap.
9
9
9
9
9 Using a higher setting for CELL than for PITCH can result in
wide gaps between characters.
Set Number of Lines Per Inch
LPI lets you specify how many lines to print per inch. You can select
2, 3, 4, 5, 6, 8, 9, 10 or 12 lines per inch. If the current setting is
Other, then your software application has set the number of lines per inch
to some nonstandard value.
Set Color
COLOR lets you specify a color for printing. You can select Black,
Cyan (light blue), Mgnta (magenta), Yellw (yellow), Violt (violet),
Green or Orang (orange). If a monochrome ribbon is installed, the
printer ignores your color selection.
Turn Italic Mode On and Off
ITALICS lets you turn the italic mode on and off. In the italic mode,
characters slant to the right by about 20%. You can select On or Off.
15) CELL:
10
16) LPI:
10
ABCDEFGHIJKLMN
ABCDEFGHIJKLMN
ABCDEFGHIJKLMN
ABCDEFGHIJKLMN
ABCDEFGHIJKLMN
ABCDEFGHIJKLMN
ABCDEFGHIJKLMN
ABCDEFGHIJKLMN
17) COLOR: Black
18) ITALICS: Off