beautypg.com

Draw-Tite 36116 FRAME HITCH User Manual

Installation instructions, Part numbers

background image

Installation Instructions

FORD LTD & CROWN VICTORIA

LINCOLN TOWN CAR, TOWN COUPE & MARK VI

MERCURY MARQUIS & GRAND MARQUIS

FORD-LTD & COUNTRY SQUIRE WAGONS

MERCURY MARQUIS & COLONY PARK WAGONS

MERCURY MARAUDER

Part Numbers:

06043

36116

90139

Wiring Access Location: PC1 & PC2

Equipment Required:

Wrenches: 3/4, 13mm
Drill Bits: 1/2

*

NOTE: 1995-1997, 2003 & LATER LINCOLN TOWN CAR EXTERNAL DRESS PANEL BENEATH VEHICLE MUST BE REMOVED FOR HITCH

INSTALLATION AND RETURNED TO VEHICLE OWNER.

1.

Examine bottom of frame rails of vehicle. To allow the hitch to sit flat, any weld spatter must be removed from frame rails. Remove all but thin

film of undercoating from attaching surfaces.

2.

Raise hitch into position on frame rails making sure that it is centered on vehicle. Hitch should be positioned so that side brackets are

approximately 1” from the rear end of frame.

NOTE: On 2003 & Later Lincoln Town Car, it will be necessary to relocate passenger side exhaust hanger bracket as follows: Unbolt hanger

bracket from vehicle frame. Remove rubber hanger from hanger bracket and tail pipe bracket, see Figure 3. Rotate rubber hanger and

reattach to hanger bracket as shown in Figure 4. DO NOT reattach to tail pipe bracket at this time. Discard existing exhaust hanger bolt.

3.

Using hitch as a template, drill four (4) holes in frame. The rear holes should be drilled as close to the center to the of the vehicle as possible.

4.

Drop 1/2 hex bolt with 1/4 X 1-1/2 X 2 block down thru opening at end of each frame rail for rear attachment point. Forward attachment point

requires fish wiring 1/2 carriage bolt with 1/4 X 1-1/2 X 2 block thru body mount access hole into drilled hole.

5.

Install 1/4 X 1-1/2 X 2 block with round hole between frame and hitch as shown for rear attachment.

6.

Install conical washers and hex nuts.

7.

Reattach exhaust hanger as shown in Figure 4.

Rev. D

12-9-05

N36116

Sheet 1 of 6

z

1994, 1999, 2002 & 2005 Cequent Towing Products

Block 1/4 X 1.50 X 2.00

Qty. (6)

6

Taper Block

Qty. (2)

Hex Bolt 1/2-13 X 2.00

Qty. (2)

5

Hex Nut M8 X 1.25

Qty. (1)

Hex Nut 1/2-13

Qty. (4)

4

Lock Washer 5/16

Qty. (1)

9

Conical Washer 1/2

Qty. (4)

3

Block 3/16 X 1.00 X 2.00

Qty. (1)

8

Block 1/4 X 1.50 X 2.00

Qty. (4)

2

Hex Bolt M8 X 1.25 X 30mm

Qty. (1)

7

Carriage Bolts 1/2-13 X 1.75

Qty. (2)

1

Tighten all 1/2 -13 fasteners with torque wrench to 75Lb.-Ft. (102 N*M)

Tighten all M8 fasteners with torque wrench to 20Lb.-Ft. (27 N*M)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

3500 LB (1589 Kg) Max Gross Trailer Weight

300 LB (136 Kg) Max Tongue Weight

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Drawbar must be used in the
RISE position only.

Drawbar Kit:

36063

Fastener Kit: 01130-445

11

12

* 1984-Later Lincoln Town Car only

Existing hanger bolt
to be discarded

Hanger bracket

Rubber exhaust
hanger

Tail pipe bracket
mounting hole

Hitch side bracket

Access hole

Access hole

Drilled hole

Drilled hole

Reattach Passenger side
exhaust hanger bracket
this hole 2003 & Later
Lincoln Town Car only
See Figure 4

FIGURE 3

Existing passenger side exhaust hanger

arrangement – 2003 & Later Lincoln

Town Car only

FIGURE 4

Modified passenger side exhaust hanger

arrangement - 2003 & Later Lincoln

Town Car only

FIGURE 1

FASTENERS TYPICAL BOTH SIDES

Frame

Frame rail

SEDAN ONLY

Form F206 Rev A 5605