Draw-Tite 41920 ULTRA FRAME RECEIVER - Manual

Installation Instructions
Ford – F-Series Pickup Truck
Ford Supercrew Pickup Truck
Part Numbers:
41920
Hitch Shown In Proper Position
Equipment Required:
Wrenches: 3/4” , 13/16”, 7/8”
Drill Bits: 1/2”
NOTE: DUE TO VEHICLE AND TIRE SIZE VARIATION SPARE TIRE MAY HAVE TO BE LOOSENED TO INSTALL HITCH.
1. SCRAPE WAX COATING OFF OF FRAME RAILS AROUND THE EIGHT ATTACHMENTS.
2. INSERT 9/16” HEX BOLTS, HARDENED FLAT WASHERS, AND REINFORCEMENT BRACKETS IN REARMOST ATTACHMENT HOLES IN EACH
FRAME RAIL.
3. RAISE HITCH INTO POSITION AND LOOSELY INSTALL FASTENERS AT THE REAR ATTACHMENTS.
4. INSTALL 9/16” HEX BOLTS, HARDENED FLAT WASHERS, AND BLOCKS THRU FORWARD ATTACHMENTS HOLES AND FASTEN WITH
LOCKNUTS.
5. USE REINFORCEMENT BRACKET AS A TEMPLATE TO DRILL A 1/2" HOLE THRU THE BUMPER BRACKET INTO THE EXISTING SLOT IN THE
FRAME RAIL EACH SIDE.
6. INSERT 1/2” HEX BOLTS, HARDENED FLAT WASHERS THRU REINFORCEMENT BRACKETS AND FASTEN WITH HARDENED FLAT WASHERS,
LOCK WASHERS AND NUTS.
Tighten all 9/16” fasteners with torque wrench to 110 Lb.-Ft. (149 n*m)
Rev. A 3-11-08 N41920 Sheet 1 of 1 z 2008 Cequent Towing Products
HEX NUT – 1/2”-13 Qty. (2) 5
FLANGED LOCKNUT – 9/16”-18 Qty. (8) 9 LOCK WASHER – 1/2” Qty. (2) 4
BLOCK – 1/4 X 1-1/2 X 4.00 Qty. (2) 8 REINFORCEMENT BRACKET Qty. (2) 3
HARDEN FLAT WASHER – 9/16” Qty. (8) 7 HARDEN FLAT WASHER – 1/2” Qty. (4) 2
HEX BOLT – 9/16” -18 X 2” Qty. (8) 6 HEX BOLT – 1/2”-13 X 1 3/4” LONG Qty. (2) 1
Tighten all 1/2” fasteners with torque wrench to 75 Lb.-Ft. (102 n*m)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
Fastener Kit: F41920
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rating or
1,000 (454 kg) 10,000 (4540 kg)
Weight Carrying
Ball Mount
1,300 (590 kg) 13,000 (5902 kg) Weight Distributing
Max Tongue
WT (LB)
Max Gross
Trailer WT (LB)
Hitch type
Wiring Access Location: PU1, PU2
Form: F205 Rev A 5-6-05
1
2
3
45
67
8
9
6 7
2
EXISTING SLOT IN FRAME
COVERED BY BUMPER BRACKET
ON INSIDE OF FRAME
FRAME RAIL
BUMPER BRACKET
REQUIRES DRILLING
STEP BUMPER
REINFORCEMENT
BRACKET