Atec Agilent-E8364A - Manual (Page 17)

17
Test port input
Description Specification Supplemental information
Standard 014 UNL UNL and 014
Test port noise floor 1
10-Hz IF bandwidth
45 to 500 MHz 2 < -89 dBm < -89 dBm < -89 dBm < -89 dBm
500 MHz to 2 GHz < -114 dBm < -114 dBm < -114 dBm < -114 dBm
2 to 10 GHz < -117 dBm < -117 dBm < -117 dBm < -117 dBm
10 to 20 GHz < -120 dBm < -119 dBm < -120 dBm < -119 dBm
20 to 40 GHz < -114 dBm < -113 dBm < -114 dBm < -113 dBm
40 to 50 GHz < -114 dBm < -112 dBm < -114 dBm < -112 dBm
1-Hz IF bandwidth
45 to 500 MHz 2 < -69 dBm < -69 dBm < -69 dBm < -69 dBm
500 MHz to 2 GHz < -94 dBm < -94 dBm < -94 dBm < -94 dBm
2 to 10 GHz < -97 dBm < -97 dBm < -97 dBm < -97 dBm
10 to 20 GHz < -100 dBm < -99 dBm < -100 dBm < -99 dBm
20 to 40 GHz < -94 dBm < -93 dBm < -94 dBm < -93 dBm
40 to 50 GHz < -94 dBm < -92 dBm < -94 dBm < -92 dBm
Direct receiver access input noise floor 1
10-Hz IF bandwidth
45 to 500 MHz 2 < -127 dBm < -127 dBm
500 MHz to 2 GHz < -133 dBm < -133 dBm
2 to 10 GHz < -132 dBm < -132 dBm
10 to 20 GHz < -134 dBm < -134 dBm
20 to 40 GHz < -125 dBm < -125 dBm
40 to 50 GHz < -123 dBm < -123 dBm
1-Hz IF bandwidth
45 to 500 MHz < -107 dBm < -107 dBm
500 MHz to 2 GHz < -113 dBm < -113 dBm
2 to 10 GHz < -112 dBm < -112 dBm
10 to 20 GHz < -114 dBm < -114 dBm
20 to 40 GHz < -105 dBm < -105 dBm
40 to 50 GHz < -103 dBm < -103 dBm
Receiver compression level
45 MHz to 20 GHz < 0.6 dB compression at +5 dBm
20 to 30 GHz < 0.6 dB compression at 0 dBm
30 to 40 GHz < 0.6 dB compression at -3 dBm
40 to 50 GHz < 0.6 dB compression at -3 dBm
System compression level max output power See dynamic accuracy chart
Trace noise magnitude
45 to 500 MHz < 0.010 dB rms 1-kHz IF bandwidth
500 MHz to 20 GHz < 0.006 dB rms Ratio measurement, nominal
20 to 40 GHz < 0.006 dB rms power at test port
40 to 50 GHz < 0.006 dB rms
Trace noise phase
45 to 500 MHz 3 < 0.100° rms 1-kHz IF bandwidth
500 MHz to 20 GHz < 0.060° rms Ratio measurement, nominal
20 to 40 GHz < 0.100° rms power at test port
40 to 50 GHz < 0.100° rms
1. Total average (rms) noise power calculated as
mean value of a linear magnitude trace expressed
in dBm.
2. Noise floor may be degraded by 10 dB at particular
frequencies (multiples of 5 MHz) due to spurious
receiver residuals.
3. Trace noise magnitude may be degraded to
20 mdB rms at harmonic frequencies of the first IF
(8.33 MHz) below 80 MHz.