Commands – Extron Electronics FOX Matrix 7200 User Manual
Page 76
X6$
= Port timeout (10‑sec. increments) 1 (= 10 seconds) – 65000 (default is 30 = 300 seconds = 5 minutes)
X6%
= SMNP port number
00000 (= disable) – nnnnn. Default = 00161. Leading zeroes are not necessary for entry.
X6^
= SNMP contact name and location Up to 64 alphanumeric characters. Default = Not•Specified.
X6&
= SNMP community name
Up to 64 alphanumeric characters.
Default = public (for read community) or private (for read‑write community).
X6*
= Trap target
1 – 3
X6(
= SNMP trap version
2 or 3, or 0 = empty (default) if no target set
X7)
= SNMP target 1 through 3
70 – 72. 70 = SNMP target 1, ... 72 = target 3
Command and Response Table for IP- and SNMP-Specific SIS Commands
Command Function
SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional description
IP setup commands
Set matrix name
EX4)
CN
}
Ipn•
X4)]
Read matrix name (location)
E
CN
}
X4)]
Reset matrix name to factory default
E
•CN
}
Ipn•
X4)]
“FOX-Matrix-3
(
7
)‑”
plus the last
3 pairs of the MAC address.
Set time and date
E
X4@
CT
}
Ipt
X4@]
Read time and date
E
CT
}
X4#]
Set GMT offset
EX4$
CZ
}
Ipz
X4$]
In the command, the divider between
hours and minutes can be either a
colon or a period. In the response, the
divider is a colon.
Example:
E
8.3CZ
}
Ipz+08:30
]
8.3 = 8:30
Read GMT offset
E
CZ
}
X4$]
Set Daylight Saving Time
EX4%
CX
}
X4%]
Read Daylight Savings Time
E
CX
}
X4%]
Set IP address
EX4^
CI
}
Ipi
X4^]
Read IP address
E
CI
}
X4^]
Read hardware address
E
CH
}
X4&]
Reads MAC address.
Read # of open connections
E
CC
}
X4*]
Set subnet mask
EX4^
CS
}
Ips
X4^]
Read subnet mask
E
CS
}
X4^]
Set gateway IP address
EX4^
CG
}
Ipg
X4^]
Read gateway IP address
E
CG
}
X4^]
Set administrator password
EX4(
CA
}
Ipa•
X4(]
Read administrator password
E
CA
}
X4(]
Reset (clear) administrator
password
E
•CA
}
Ipa•
]
Set user password
EX4(
CU
}
Ipu•
X4(]
Read user password
E
CU
}
X4(]
Reset (clear) user password
E
•CU
}
Ipu•
]
Set mail server, domainname
EX4^
,
X5)
,
X4(
CM
}
Ipm
X4^
,
X5)
,
X4(]
Read mail server, domainname
E
CM
}
X4^
,
X5)
,
X4(]
Set e‑mail recipient
EX5!
,
X5@
CR
}
Ipr
X5!
,
X5@
,
]
This command sets the e‑mail recipient.
To receive e‑mail notifications, you must
then set the events that the switcher
reports, using one or more separate
(EM) SIS commands (on the
next page).
Example:
E
}
Ipr69,[email protected],
]
Read e‑mail recipient
EX5!
CR
}
X5@
,
]
FOX Matrix 3200 and 7200 Switchers • Programming Guide
68