Extron Electronics FOX Matrix 7200 User Manual
Page 68
Command and Response Table for SIS Commands (continued)
Command Function
SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional description
Reclocking
NOTES:
• Laser board reclockers are set on a per SFP basis. If an SFP is reclocked, the corresponding input and output reclockers reclock
at the same rate.
• HD‑SDI reclockers are set on a per output basis only.
Set output reclocker
X$
*
X%
=
Rte
X$
*
X%]
Set the rate for reclocker
X$
to
X%
.
Example:
8*00=
Rte08*00
]
Set the rate for reclocker 8 to auto.
Read reclocker status
X$
=
X%]
Show current rate status for reclocker
X$
.
Laser controls
Enable individual laser driver
EX!
*1FIBR
}
Fibr
X!
*1
]
Enable the laser for output
X!
. The laser lights
so long as power is applied.
Disable individual laser driver
EX!
*0FIBR
}
Fibr
X!
*0
]
Disable the laser for output
X!
. The laser is off.
Set individual output laser
driver to automatic
EX!
*2FIBR
}
Fibr
X!
*2
]
Set the laser driver for output
X!
to automatic.
The laser lights when a tie is made to output
X!
,
but is off when no tie is made to output
X!
or
the output is muted.
Read status of all laser
drivers
E
FIBR
}
X^
1
X^
2
X^
3
X^
4
...
X^
n
]
List the laser driver status of all installed outputs.
n is the highest numbered output for your switcher.
Global laser enable
E
1*FIBR
}
Fibr1]
Enable all output laser drivers.
NOTE: If your switcher has any BNC 3G/HD/SD‑SDI boards installed, the global commands are not available. The switcher returns E14.
Global laser disable
E
0*FIBR
}
Fibr0]
Disable all output laser drivers.
Global laser automatic
E
2*FIBR
}
Fibr2]
Set all output laser drivers to automatic.
Save, recall, and directly write global presets
NOTES:
•
If you try to recall a preset that is not saved, the matrix switcher responds with the error code E11.
•
The following characters are invalid or not recommended in preset names: + - , ` @ = [ ] { } ‘ “ ; : | \ and ?.
Save current configuration
as a global preset
X&
,
Spr
X&]
Command character is a comma.
Example:
8,
Spr08
]
Save current ties as preset 8.
Recall a global preset
X&
.
Rpr
X&]
Command character is a period.
Example:
5.
Rpr05
]
Recall preset 5 (becomes the current configuration).
Direct write process —
NOTE: The direct write of a global preset should always be preceded by a clear global preset ties command of that same preset number.
In a directly‑written preset, the tied input of each output position (or no tied input) remains unchanged unless overwritten or cleared.
If you do not clear the ties in a global preset number before you directly write a global preset to that number, ties that are part of the
previous version of the specified preset with the same number can unexpectedly become part of the newly‑created preset.
Clear global preset ties
E
+
X&
P0*!
}
Spr
X&]
Clear all ties in preset
X&
.
Directly write a global preset
E
+
X&
P
X!
*
X@
!
X!
*
X@
%
X!
*
X@
! ...
X!
*
X@
&
}
Enter as many ties as are valid for this
configuration. The
!
tie,
&
tie, and
%
tie
commands are all valid.
Spr
X&]
Example:
E
+27P0*!
}
Spr27
]
Clear all ties in preset 27.
Esc
+27P12*5!10*09%3*2!3*8&
Brackets are shown to separate ties for clarity
only. Create global preset 27, which ties input
12 to output 5, input 10 to output 9, input 3 to
output 2, and input 3 to output 8.
Spr27
]
NOTE:
X!
= Input number (for tie)
00 – (maximum number of inputs for your configuration) (00 = untied)
X@
= Output number
01 – (maximum number of outputs for your configuration)
X$
= SFP or reclockable output
00 – 32 or 72 (00 = global [SFP only])
X%
= Output reclocking rate
00 = Bypass mode
01 = Automatic mode (HDSDI boards only)
03 = 2.125 Gbps (laser boards only)
02 = 1.250 Gbps (laser boards only)
04 = 4.250 Gbps (laser boards only)
X^
= Laser control
0 = disable
1 = enable (default)
2 = automatic
X&
= Global preset number
00 – 32 (FOX Matrix 3200) or 64 (FOX Matrix 7200) (00 = current configuration)
FOX Matrix 3200 and 7200 Switchers • Programming Guide
60