Xylem 795 MJK Data Transmitter - Manual (Page 4)

4 M795GB0503
Data Transmitter 795
SW ver. 830434
10 Programming of logical functions ..... 21
10.1 Select the output to receive the result
of the logical function .................................. 21
10.2 Select logical function ................................. 21
10.2.1
Select signals for the logical function 21
10.2.2 Operational or alarm signal on
internal flag
22
10.2.3 Dialout when alarm signal on
internal flag
22
10.2.4 Signal delay on internal flag 22
11 Programming of interlock .................. 22
11.1 Interlock of this station ................................ 22
11.2 Interlock interval .......................................... 22
11.3 Selection of substation ............................... 22
11.4 Interlock active / inactive ............................ 23
11.4.1
Start of interlock 23
11.4.2 Stop interlock 23
11.4.3 Receivers telephone / ID number 23
11.4.4 Receiver's output 24
12 Programming of Pump Controller(s) . 25
12.1 704 connected ........................................... 25
12.2 Call on alarm or system error on 704 .......... 25
12.2 Programming of the
internal Pump Controller ............................. 25
12.2.1 Select level signal 25
12.2.2 Start level for pump no. 1 25
12.2.2 Stop level for pump no. 1 25
12.2.3 Levels in use in 795 25
12.2.4 Start level for pump no. 2 25
12.3.2 Stop level for pump no. 2 25
12.3.3 Alternation of pumps 25
13 Telephone list for alarms ................... 26
13.1 Telephone number 1-9 ............................... 26
13.2 Number type .............................................. 26
13.2.1
Telephone number 26
13.2.2 Enter pager message 26
13.2.3 Enter SMS message 27
13.2.4 Pause between calls 27
14 Programming of stormflow calculation .. 27
14.1 Stormflow calculation ................................. 27
14.2 Stormflow calculation in use ....................... 28
14.2.1
Zero point input no. 28
14.2.2 Level signal for flow calculation 28
14.2.3 Number of Q(h) points 28
14.2.4 Height value [h] for level point 28
14.2.5 Flow value [Q] for level point 28
15 Programming of 702 ComTroller ....... 29
15.1 Select 702 .................................................. 29
16 Alarms ................................................. 30
16.1 Operational or alarm signal ......................... 30
16.2 Alarm calls .................................................. 30
16.3 Reset of alarms .......................................... 30
15.3.1
Automatic reset of alarms 30
17 Factory settings ................................. 31
18 Signal lists .......................................... 33
19 Register list ......................................... 37
20 Menu structure ................................... 44
20.1 Functional menus ....................................... 44
20.2 Programming menus .................................. 45
A Appendix ............................................. 50
A1 Technical specifications .............................. 50
A2 Number of signals available ........................ 50
A3 Inputs and outputs ..................................... 50
A4 Dimensions ................................................. 50
B Appendix ............................................. 51
B1 Maintenance ............................................... 51
B2 Service codes ............................................. 51
B2.2 Forced setup
without reset of datalogger
51
B2.3 Forced setup
including reset of datalogger
51
B2.4 Baud rate and communication method 51
B2.5 Activation of SIM card for GSM/GPRS
modem
51
B2.6 Total reset 51
B3 Software upgrade ....................................... 51
B4 SMSC telephone numbers ......................... 52
B5 Spare parts ................................................. 52