beautypg.com

Installation guide, Setup, Entering setup mode – Veris Industries H8936 Install User Manual

Page 7: Setup mode sub-menus, Status led and relay operation, Monitoring mode, Alarm mode

background image

Z202662-0G

PAGE 7

©2012 Veris Industries USA 800.354.8556 or 1.503.598.4564 / [email protected]

09126

Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.

TM

H8932/H8936

INSTALLATION GUIDE

SETUP

Use the Setup mode to initialize and configure the display to the application
requirements. Use Setup Sub-menus to group parameters for setup.

Entering Setup Mode

UP

DOWN

To Enter

(SELECT, DOWN, DOWN, SELECT, UP, UP)

UP

SELECT

DOWN

METER

Show next
submenu

Show previous
submenu

Return to
monitoring

Go to submenu
or start action

Setup Mode

Press Simultaneously

Press

Enter Password

* * * * * * *

Setup Mode Sub-Menus

After entering the password (Select, Down, Down, Select, Up, Up), the device enters
the Setup Mode Sub-Menus. Scroll through these menus using the Up or Down
buttons, and enter a menu by pressing Select.

1. VIEW SYSTEM INFO: Lists the model number and firmware version of the device.

2. FIND METERS: Initiates a search and identifies meters on the network. Exit the

search by pressing any key (do not exit until all active addresses have been
counted). Unsupported devices are designated as “unknown device,” and
parameters are not displayed.

3. REVIEW METERS: Review all meters on the network.

4. SETUP COMMUNICATIONS: Scroll through this list of available parameters using

the Select button; change a parameter value using the Up and Down buttons.

Increment
parameter

Decrement
parameter

Return to
setup menu

Go to next
parameter

DOWN

UP

SELECT

METER

Communications Parameters:

Address Routing (On, Off)
Modbus Address (1-247)
Upstream Type (RS-485, RS-232)
Upstream Duplex (2-wire, 4-wire) (not available for RS-232)
Upstream Baudrate (2400, 4800, 9600, 19200)
Upstream Parity (NONE, ODD, EVEN)
Downstream Duplex (2-wire, 4-wire)
Downstream Baudrate (2400, 4800, 9600, 19200)
Downstream Parity (NONE, ODD, EVEN)

5. SETUP OPERATION: Scroll through this list of available parameters using the Select

button; select a parameter value using the Up and Down buttons.

Increment
parameter

Decrement
parameter

Return to
setup menu

Go to next
parameter

DOWN

UP

SELECT

METER

Operation Parameters:

Backlight Brightness (0-9; 0 = off)
Auxiliary Input (open, closed)
Rotate Parameters (Yes, No)

Status LED and Relay Operation

The status LED displays the condition of the alarm registers on a color cue basis.

Green: normal operation (no networked devices are in warning or alarm
mode)
Yellow: warning (one or more networked devices are in warning mode)
Red: alarm (one or more networked devices are in alarm mode or the
auxiliary input is active).

Monitoring Mode

Monitoring mode is the default mode for the H8932/H8936. In monitoring mode, the
data values are updated at 4-second intervals. The H8932/H8936 can be set either
to cycle automatically through all parameters on all devices or to display a selected
parameter continuously.

Go to the next

parameter set.

Go to the previous

parameter set.

Go to the

next meter

Hold a reading on

the LCD (display will

flash).

For use in automatic

cycle mode (See Setup

Operations).

The current reading does

not update, allowing time

to manually record the

reading. Press any

other button to release

the held reading.

DOWN

UP

SELECT

METER

Alarm Mode

Alarm Mode provides a means of viewing and resetting warnings and alarms on the
downstream network. To enter Alarm mode, press the Select and Meter buttons
simultaneously.

Go to the
next alarm.

Reset the currently
displayed alarm.

Exit the alarm
display.

To Enter

Alarm Menu

Press Simultaneously

Press

UP

SELECT

SELECT

METER

METER