Wayne-Dalton TORQUEMASTER 9800 - Manual (Page 32)

Tools Needed:
32
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer.
To find your Wayne-Dalton dealer; refer to your local yellow pages / business listings or go to Find a dealer area online at www.wayne-dalton.com
To adjust spring(s), only add or remove a
maximum of 3/10 of a turn (three teeth of
ratchet wheel) at a time. both sides need
to be adjusted equally on double spring
doors.
NOTE: single spring applications require
no spring winding on left hand side.
Clamp a pair of vice clamps on the vertical
tracks just above the second roller on one
side and just below the second roller on
the other side. This will prevent the door
from raising or lowering while adjusting
the spring(s).
PRIOR TO WINDING OR MakING
aDjusTMENTs TO ThE sPRINGs, ENsuRE
yOu’RE WINDING IN ThE PROPER
DIRECTION as sTaTED IN ThE
INsTallaTION INsTRuCTIONs.
OThERWIsE ThE sPRING FITTINGs May
RElEasE FROM sPRING IF NOT WOuND
IN ThE PROPER DIRECTION aND COulD
REsulT IN sEVERE OR FaTal INjuRy.
To Add Spring Tension: The ratchet
wheel is made of 10 teeth. To add spring
tension, ensure the ratchet and socket is
set so that it will tighten counter clockwise
on the right hand side, and clockwise on
the left hand side. Place the ratchet with
5/8” socket onto the winding shaft, pull
down to add 3/10 of a turn. Watch as
three teeth of the ratchet wheel pass over
the pawl, creating three “clicks”.
To Remove Spring Tension: To remove
spring tension, ensure the ratchet and
socket is set so that it will tighten counter
clockwise on the right hand side and
clockwise on the left hand side. Place the
wrench onto the winding shaft. Pull down
on the ratchet to relieve pressure between
the pawl and the ratchet wheel. Push in on
the pawl to allow the three ratchet wheel
teeth to pass by the pawl, as you carefully
allow the ratchet wrench to be rotated
upward by the spring tension. Release the
pawl to allow it to engage with the ratchet
wheel.
Remove the vice clamps from the vertical
tracks, re-check door balance and adjust
if necessary. When door is balanced and
adjusted properly, place the ratchet pawl
knobs in the active position (lower
position).
TorqueMaster ® Plus Reset
Instructions Continued...
TRaCk VICE ClaMPs
aTTaChED TO
TRaCk
PlaCE VICE ClaMPs
abOVE 3RD ROllER ON
bOTh VERTICal TRaCk
PaWl kNOb IN lOWER
POsITION
LOwER POSITION UPPER POSITION
Cab le Dr um
No sp ace betw een Ratche t
Pawl an d Cabl e Dr um indica tes engage ment
Cabl e Dr um Ratc het Paw l
ENG AGE D SIDE VIEW
No sp ace bet ween Ratchet Paw l and Cabl e Dr um
ENGA GED UNDE RNE ATH VIEW
Space betwe en Rat chet P awl and Cable Drum non- indica tes en gag ement
Cabl e Dr um
Ratche t Paw l
DISENG AGE D SIDE VI EW
No sp ace betwe en Ratche t Paw l and
DISENG AGE D UNDE RNE ATH VIEW
UPP ER POSIT ION
LOWER POS ITION
LOWER POSIT
ION SID E VIEW
UPP ER POSI TION SI DE VIE W
Ratc het Pawl i n Lo wer Posi tion
Ratche t Paw l in Upper Pos ition
Use these Illus tration , in conj uncti on wi th th e Instruction
s on the other si de of
this label. WAR
NING Rachet Bracke
t is under
EXTREME SPRING
TENS ION.
To avoid
possible sev
ere or
fatal injury
, DO NO
T remove
fasteners
from ratchet
bracket
until spr ing(s) are fu lly
wnwound
.
To safely unwind spr
ing(s) read and fo llow the dire
ctions in the
installati
on instructio
ns/owners manual
.
DO NO
T REMOVE
THIS TAG .
RaTChET
WITh 5/8”
sOCkET
END bRaCkET
3” ExTENsION
PaWl kNOb IN uPPER
POsITION
PaWl
wARNINg