Wayne-Dalton TORQUEMASTER 9800 - Manual (Page 26)

Tools Needed:
26
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer.
To find your Wayne-Dalton dealer; refer to your local yellow pages / business listings or go to Find a dealer area online at www.wayne-dalton.com
Cab le Dr um
No sp ace betwe en Ratch et
Pawl and Ca ble Dr um indica tes en gagemen t
Cab le Drum Ratch et Paw l
ENGAG ED SIDE VIEW
No s pace betwee n Ratc het Paw l and Cabl e Dru m
ENGAGE D UNDE RNEA TH VIE W
Space betwe en Ratchet P
awl and Cable Drum non- indicat es engagem
ent
Cab le Dr um
Ratche t Paw l
DISENG AGED SIDE VIEW
No sp ace between Ratche t Paw l and
DISE NGAGED UNDE RNE ATH V IEW
UPPER POSIT ION
LOWER POSIT
ION
LOWER POSIT ION SIDE VIEW
UPP ER POSITION S
IDE VIEW
Ratchet Paw
l in Lowe r Po sition
Ratch et Paw l in Up per Pos ition
Use these Illu
stration , in conj unctio n wi th th e Instruction
s on th e oth er si de of
this la bel. WAR
NING Rachet Brack
et is under
EXTREM
E SPRI
NG
TENS
ION.
To avoid possible se
vere or
fata l injury
, DO NO
T remov
e
fasteners
from ratchet
bracket
until sp
ring( s) are fu
lly
wnwound
.
To safely un
wind spr
ing(s) read
and fo
llow the dire
ctions in
the
installati
on in structio
ns/owners ma nual.
DO NO
T REMOVE
THIS
TAG .
24
winding Springs
Ratchet
5/8” socket
3” Extension
Gloves
RECOMMENDED SPRINg TURNS
Door height Spring Turns
6’-6” 15
7’-0” 16
8’-0” 18
END bRaCkET
RaTChET
3”
ExTENsION
5/8” sOCkET
MaRks
IT Is RECOMMENDED ThaT lEaThER
GlOVEs bE WORN WhIlE WINDING
ThE TORquEMasTER
® Plus sPRINGs.
FaIluRE TO WEaR GlOVEs May CausE
INjuRy TO haNDs.
PRIOR TO WINDING OR MakING
aDjusTMENTs TO ThE sPRINGs,
ENsuRE yOu’RE WINDING IN ThE
PROPER DIRECTION as sTaTED IN ThE
INsTallaTION INsTRuCTIONs.
OThERWIsE ThE sPRING FITTINGs May
RElEasE FROM sPRING IF NOT WOuND
IN ThE PROPER DIRECTION aND COulD
REsulT IN sEVERE OR FaTal INjuRy.
Double check to ensure the
counterbalance cable is aligned in the
first groove of the cable drum step 28.
starting with the right hand side, place
a mark on winding shaft (or socket) and
end bracket.
Turn the pawl knob on the end bracket
to the upper position. using a ratchet
wrench with a 5/8“ socket ( NOTE: a
3” extension is also recommended for
added clearance from the horizontal
angle.), wind the spring by rotating the
winding shaft counter clockwise, while
watching the mark on the winding
shaft.
IMPORTANT: PaWl kNOb MusT bE
IN uPPER POsITION TO aDD/ REMOVE
REquIRED NuMbER OF sPRING TuRNs.
after 2-3 turns, remove the ratchet
wrench and adjust the cable on the left
side (step 28). Ensure the cables are in
the first groove and the cable drums, as
shown in step 28.
NOTE: single spring application require
no spring winding on the left hand side,
but need cable tension adjustments.
IMPORTANT: COuNTERbalaNCE
CablE TENsION MusT bE Equal ON
bOTh sIDEs PRIOR TO Fully WINDING
sPRINGs.
SEE ThE SPRINg TURN ChART fOR
ThE REqUIRED NUMBER Of TURNS:
for single spring applications:
Return to the right hand and continue
winding the spring to the required
number of turns for your door. Place
pawl knob in lower position.
for double spring applications:
Place a mark on the winding shaft and
end bracket. Place the ratchet with 5/8”
socket onto the left hand winding shaft
end.
wARNINg
PaWl kNOb IN lOWER
POsITION
END bRaCkET
PaWl kNOb IN uPPER
POsITION
END bRaCkET
wARNINg