Philips DIGA DMR-XS350EB - Manual (Page 116)

116
RQT9431
Messages
On the Unit’s Display
Page
H , F
(“ ” stands for a service
number.)
An error has occurred. The number following “H” or “F” depends on the status of the unit.
Check the items below and in the Troubleshooting Guide. If the service number still does
not disappear after the check, reset the unit ( ➔ 119, “To restore the unit if it freezes” ).
If the service numbers fail to clear, note the service numbers and contact a
qualified service person.
•
•
−
−
DVD
(“ ” stands for a number.)
The remote control and the main unit are using different codes. Change the code
on the remote control.
• 119
EXT-L This unit is in EXT LINK standby. EXT LINK has been turned on and will stop
operation on the unit until the recording has completed.
Press [EXT LINK] to stop recording or cancel linked timer.
• 62
FINISH The software update is completed. • 108
GUIDE TV Guide data is being downloaded. • 44
HARD ERR If there is no change after turning the unit on and off, consult the dealer where the
unit was purchased.
• −
NoERAS You cannot delete items on this disc.
The disc may be damaged. Use a new disc.
• −
NoREAD The disc is dirty or badly scratched. The unit cannot record, play, or edit.
The disc may be incompatible or of poor quality.
You have used a lens cleaner and it has finished operation. Press
[; OPEN/CLOSE] on the main unit to eject the disc.
•
•
•
118
21, 22
7
NoWRIT You cannot write to this disc.
The disc may be damaged. Use a new disc.
• −
PLEASE WAIT Displayed when the unit is started or when turned to standby. This is not a
malfunction.
The unit is carrying out its recovery process. You cannot operate the unit while the
message is displayed.
•
•
−
−
PROG FULL There are already 32 timer recording programmes. Delete unnecessary timer recording programmes. • 41
REMOVE The USB device is drawing too much power. Remove the USB device. • −
START Update of the software is started.
You cannot operate the unit until the update is complete.
• 108
SW-DL The unit is performing a software update.
Download will stop when the power is turned on, or the timer recording starts.
• 108
UNFORMAT You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL or
DVD-RW (DVD-Video format) that has been recorded on other equipment.
Format the disc to use it.
However all the recorded contents on the disc are deleted.
• 93
UNSUPPORT You have inserted a disc the unit cannot play or record onto.
You tried to operate with a non-compatible USB memory.
•
•
21, 22
23
UPD /
(“ ” stands for a number.)
The software is being updated.
You cannot operate the unit until the update is complete.
• 108
U50 The terminal, antenna cable or DISH is short-circuited as for both DISH IN 1 and
DISH 2. Check the connection status.
• 10, 11
U50 1 The terminal, antenna cable or DISH is short-circuited as for DISH IN 1. Check the connection status. • 10, 11
U50 2 The terminal, antenna cable or DISH is short-circuited as for DISH IN 2. Check the connection status. • 10, 11
U59 The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until
the message disappears.
Select a position with good ventilation when installing the unit. Do not block the
cooling fan on the rear of the unit.
• −
U61 (When a disc is not inserted) Displays when a malfunction has occurred during recording
or playback. This is displayed when the unit is in the recovery process to return to normal
operation; it is not broken. Once the display clears you can use the unit again.
• −
U72
U73
The HDMI connection acts unusually.
– The connected equipment is not HDMI compatible.
– Please use HDMI cables that have the HDMI logo (as shown on the cover).
– The HDMI cable is damaged.
• −
U76 HDMI cannot be output because you are connected to a model that does not
support copyright protection.
• −
U77 Due to the current disc not having authorised copyright information, video output is not performed. • −
U88 There was something unusual detected with the disc while recording, playing or
copying; there was a power failure or the AC mains lead was disconnected while the
unit was on. The unit is carrying out its recovery process. This process restores the
unit to normal operation. The unit is not broken. Wait until the message disappears.
• 121
U99 The unit fails to operate properly. Press [8] on the main unit to switch the unit to
standby mode. Now press [8] on the main unit again to turn the unit on.
• −
X HOLD The HOLD function is activated.
Press and hold [OK] and [BACK/RETURN ] at the same time until “X HOLD” disappears.
• 105
The message is alternately displayed.