Sanyo VSP-9000 - Manual (Page 89)

English
Others 88
Appendix
b b b b Message Chart
ALARM: Esc to exit PATROL: Sent 'Walk' Stop
AUX: Select function PATROL: Sent Recording "Walk" nr.
AUX: Function not available PRESET: Select function
AUX: Function not enabled PRESET: Sent Delete preset position
AUX: Sent Set PRESET: Esc to exit
AUX: Sent Reset PRESET: Sent Preset command
AUX: Sent Toggle PRESET: Sent Delete Preset
AUTOFLIP: Function not available PRESET MARK M.: Esc to exit
AUTOFLIP: Function not enabled PRESET MARK M.: Select function
AUTOFLIP: Sent enabled Autoflip SCAN: Function not enabled
AUTOFLIP: Sent Autoflip toggle SCAN: Esc to exit
AUTOFLIP: Sent Autoflip set SCAN: Sent Scan command
AUTOFLIP: Sent Autoflip reset SCAN: Sent Home
AUTOFLIP: Select function SCAN: Sent Home (Scan at posit.nr.1)
AUTOPAN: Select function SCAN: Sent "Back"
AUTOPAN: Sent Autopan Start SEQUENCE: Sent sequence
AUTOPAN: Sent Autopan Stop SETUP: Select function
AUTOPAN: Sent Autopan Toggle SETUP: Sent Line Lock increment
AUTOPAN: Function not enabled SETUP: Sent Line Lock decrement
AUTOPAN: Function not available SETUP: Sent Enabled alarm mode
CAMERA: Esc to exit SETUP: Sent Disabled alarm mode
CAMERA: Recall camera nr. SETUP: Sent Home position storage
CAMERA: Camera not enabled! SETUP: Sent Home position reset
CAMERA: Sent command SETUP: Sent Toggle Mono/Color
DOME: Sent 'camera setup' SETUP: Sent Auto Mono/Color
DOME: Sent 'dome setup modification' SETUP: Sent V- phase+
DOME: Sent 'dome setup exit' SETUP: Sent V- phase-
DOME: Sent 'Enter Menu' SETUP: Esc to exit
DOME: Function selection SETUP: Sent receiver Reset
DOME: Sent 'Move Up' TELEMETRY LINE "A": BUSY/ERROR
DOME: Sent 'Move Down' TELEMETRY LINE "B": BUSY/ERROR
DOME: Sent 'Move Left' LINE "VIDEO": BUSY/ERROR
DOME: Sent Move Right' VIDEO: Function not enabled
FOCUS: Function not enabled VIDEO: Sent camera increase
FOCUS: Select function VIDEO: Sent camera decrease
FOCUS: Sent Focus Near VIDEO: Function not available
FOCUS: Sent Focus Far VIDEO: Sent matrix sequence start
FOCUS: Sent AutoFocus VIDEO: Monitor not enabled!
FOCUS: Sent disabled AutoFocus VIDEO: Recall monitor nr.
IRIS: Function not enabled VIDEO: Sent 'Up Arrow'
IRIS: Select function VIDEO: Sent 'Down Arrow'
IRIS: Sent Iris Open VIDEO: Sent 'SEQ'
IRIS: Sent Iris Close VIDEO: Sent 'Matrix setup modification'
IRIS: Sent AutoIris VIDEO: Select function
IRIS: Sent disabled AutoIris VIDEO: Sent number
PATROL: Sent Start S.A. VIDEO: Sent 'M/A'
PATROL: Sent Toggle S.A. VIDEO: Sent 'STP'
PATROL: Function not enabled VIDEO: Sent 'CRL'
PATROL: Select function VIDEO: Sent 'ENT'
PATROL: Sent Start VIDEO: Unit not enabled
PATROL: Sent Stop VIDEO: Recall unit nr.
PATROL: Sent Toggle VIDEO: Dvr not enabled
PATROL: Sent enabled Pattern VIDEO: Mux not enabled
PATROL: Sent Pattern Definition VIDEO: Recall Dvr nr.
PATROL: Sent Pat.Definition End VIDEO: Recall Mux nr.
PATROL: Sent Apple peel VIDEO UNIT: Sent command
PATROL: Sent standard Setup WIPER/WASHER: Functions not available
PATROL: Sent default pause time WIPER/WASHER: Function not enabled
PATROL: Sent Start/End WIPER/WASHER: Select function
PATROL: Sent single pause time WIPER/WASHER: Sent Wiper
PATROL: Sent Start 1 WIPER/WASHER: Sent Washer
PATROL: Sent Start 2 MATRIX TIMEOUT ALARM
PATROL: Sent Start 3 MATRIX ALARM
PATROL: Sent Start 4 MONITOR: Esc to exit
PATROL: Sent position ZOOM: Function not enabled
PATROL: Esc to exit JOYSTICK: Function not enabled
PATROL: Sent "SEQUENCE" DVR/MUX: Function not enabled
PATROL: Sent "TOUR" DVR: Esc to exit
PATROL: Sent 'One Pass' Start MUX: Esc to exit
PATROL: Sent 'Walk' Start nr. Esc to exit
TOUR
ON
FOCUS
NEAR
IRIS
ADDRESS ?
C A M 1 D V R 1 C A M 1 D V R 1 Message display