JVC RX-9010VBK - Manual (Page 72)

69
English
To change the transmittable signals for
operating a CATV converter and DBS tuner
1. Set TV/CATV/DBS selector to “CATV/DBS.”
2. Press and hold TV/CATV/DBS POWER.
3. Press TV/DBS.
4. Enter manufacturer’s code using buttons 1–9,
and 0.
See pages 70 and 71 to find the code.
5. Release TV/CATV/DBS POWER.
After setting TV/CATV/DBS selector to “CATV/DBS,” you can
turn on and off the CATV convertor or on the DBS tuner:
TV/CATV/DBS POWER: Turns on and off the CATV converter
or DBS tuner.
After pressing TV/DBS with TV/CATV/DBS selector set to
“CATV/DBS,” you can perform the following operations on the
CATV convertor or on the DBS tuner:
CHANNEL +/–: Changes the channels.
1 – 10, 0, 100+ (+10): Selects the channels.
The 10 button will function as the
ENTER button if your equipment
requires pressing ENTER after
selecting a channel number.
Note:
Refer to the manual supplied with your CATV convertor or DBS
tuner.
6. Try to operate your CATV converter or DBS
tuner by pressing TV/CATV/DBS POWER.
When your CATV converter or DBS tuner turns on or off, you
have entered the correct code.
If there are more than one code listed for your brand of
CATV converter or DBS tuner, try each one until the correct
one is entered.
Note:
You cannot use this remote control for both of the CATV converter and
DBS tuner at the same time.
To change the transmittable signals for
operating another manufacturer’s VCR
1. Press and hold VCR 1 POWER.
2. Press VCR 1.
3. Enter manufacturer’s code using buttons 1–9,
and 0.
See page 71 to find the code.
4. Release VCR 1 POWER.
The following button can be used for operating the VCR :
VCR 1 POWER: Turns on and off the VCR.
After pressing VCR 1, you can perform the following operations
on the VCR:
CHANNEL +/–: Changes the TV channels on the
VCR.
1 – 10, 0, 100+ (+10): Selects the TV channels.
The 10 button will function as the
ENTER button if your VCR requires
pressing ENTER after selecting a
channel number.
PLAY: Starts playback.
REW: Rewinds a video tape.
FF: Fast-winds a video tape.
STOP: Stops operation.
PAUSE: Pauses.
¶ REC and PAUSE : Enters recording pause (for the main
room only).
¶ REC and PLAY : Starts recording (for the main
room only).
Note:
Refer to the manual supplied with your VCR.
5. Try to operate your VCR by pressing
VCR 1 POWER.
When your VCR turns on or off, you have entered the correct
code.
If there are more than one code listed for your brand of
VCR, try each one until the correct one is entered.
To change the transmittable signals for
operating a DVD player
1. Press and hold VCR 1 POWER.
2. Press DVD.
3. Enter manufacturer’s code using buttons 1–9,
and 0.
See page 71 to find the code.
4. Release VCR 1 POWER.
After pressing DVD or DVD MULTI, you can perform the
following operations on a DVD player:
1 – 9, 0, +10 : Selects the titles or the tracks.
PLAY : Starts playing.
4: Returns to the beginning of the current (or
previous) track.
¢: Skips to the beginning of the next track.
STOP : Stops playing.
PAUSE : Stops playing temporarily. To release it, press
PLAY.
EN62-74.RX-9010VBK[C]f 01.4.13, 5:40 PM 69