JVC RX-9010VBK - Manual (Page 34)

31
English
Selecting the Analog or Digital Input
Mode
When you have connected digital source components using the
digital terminals (see page 10), you need to change the input mode
for these components to the appropriate digital input mode correctly
— DGTL AUTO, DGTL DTS, or DGTL D.D.
TV SOUND/DBS VIDEO VCR 2 VCR 1 DVD DVD MULTI
FM / AM USB AUDIO TAPE / MD CDR CD PHONO
SOURCE NAME
ANALOG DGTL AUTO
(Digital)
Before you start, remember...
• The digital input (DIGITAL IN) terminal setting should be
correctly done for the sources you want to select the digital
input mode for. Without setting this digital input terminal
correctly, you cannot change the input mode from analog input to
digital input even if you follow the procedure below.
• The digital input can be used for the main room sources. The analog
input is always selected as the sub-room source without respect to
this setting.
On the front panel:
1. Press one of the source selecting button (DVD,
TV SOUND/DBS, CD, CDR, or TAPE/MD)* for
which you want to change the input mode.
The lamp on the front panel button for selected source lights up.
Note:
* You can select the digital input only for the sources which you
have selected the digital input terminals for. (See “Digital Input
(DIGITAL IN) Terminal Setting” on page 30.)
2. Press INPUT ANALOG/DIGITAL
briefly to change the input mode.
• Each time you press the button, the input
mode changes as follows:
DGTL AUTO: Select this for the digital input mode. The
receiver automatically detects the incoming
signal.
always lights up on the display, and
the digital signal indicator for the detected
signals also lights up.
ANALOG: Select this for the analog input mode.
ANALOG always lights up.
When selecting “DGTL AUTO”, following indicators showing detected
signals light up on the display.
LINEAR PCM : Lights up when Linear PCM signals come in.
• Flashes while seaching the incoming signals.
LINEAR PCM : Lights up when the digital signals are not
recognized.
DIGITAL : Lights up when Dolby Digital signals come in.
: Lights up when DTS Digital Surround signals
come in.
INPUT
ANALOG/DIGITAL
INPUT ATT
To set the DIGITAL 2/3/4 terminals:
1. Press SETTING until DIGITAL 2/3/4
terminals setting appears on the
display.
The display changes to show the current settings
for the DIGITAL 2/3/4 terminals.
SETTING
CONTROL
DOWN UP
2. Press CONTROL UP
5/DOWN ∞
to select the appropriate digital
terminal settings.
• Each time you press the buttons, the
display changes to show the following:
When the DGTL COAX (DIGITAL 1) is set to “DVD”
2: CD 3: TV (or DBS*) 4: CDR “ 2: CD 3: TV (or DBS*) 4:MD** “
2: CD 3: MD** 4: CDR “ 2: MD** 3: TV (or DBS*) 4: CDR “
(back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to “MD”**
2: CD 3: TV (or DBS*) 4: CDR “ 2: CD 3: TV (or DBS*) 4: DVD “
2: CD 3: DVD 4: CDR “ 2: DVD 3: TV (or DBS*) 4: CDR “
(back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to “CDR”
2: CD 3: TV (or DBS*) 4: DVD “ 2: CD 3: TV (or DBS*) 4: MD** “
2: CD 3: MD** 4: DVD “ 2: MD** 3: TV (or DBS*) 4: DVD “
(back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to “TV” or “DBS”
2: CD 3: DVD 4: CDR “ 2: CD 3: DVD 4: MD** “
2: CD 3: MD** 4: CDR “ 2: MD** 3: DVD 4: CDR “
(back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to “CD”
2: DVD 3: TV (or DBS*) 4: CDR “ 2: DVD 3: TV (or DBS*) 4: MD** “
2: DVD 3: MD** 4: CDR “2: MD** 3: TV (or DBS*) 4: CDR “
(back to the beginning)
* If you have changed the source name from “TV” to “DBS,”
“DBS” appears (see page 33).
** Change the source name to “MD” for TAPE/MD jacks when you
use an MD recorder (see page 33).
Note:
When shipped from the factory, the DIGITAL IN terminals can be used
as the digital input for the following components:
• DIGITAL 1 (coaxial): For DVD player
• DIGITAL 2 (optical): For CD player
• DIGITAL 3 (optical): For digital TV broadcast tuner
• DIGITAL 4 (optical): For CD recorder
DIGITAL 3 terminal setting DIGITAL 4 terminal setting
DIGITAL 2 terminal setting
EN27-36.RX-9010VBK[C]f 01.4.13, 5:39 PM 31