JVC RX-9010VBK - Manual (Page 38)

35
English
Indicates the functions YOU CAN ALSO USE when
the receiver is ready for the sub-room operations.
IMPORTANT:
Check to see if the proper indicator(s) and information(s) appear on
the display on the front panel before/while using the buttons and
controls.
When using the buttons and controls on the front panel:
• For the main room operations
– The MAIN ROOM indicator is lit.
– The source name for the sub-room is not lit on
the display.
• For the sub-room operations
– The SUB ROOM indicator is lit.
– The source name for the sub-room is lit on the
display.
When using the remote control:
• For the main room operations
– Set MAIN ROOM/SUB ROOM selector to
“MAIN ROOM.”
• For the sub-room operations
– Set MAIN ROOM/SUB ROOM selector to
“SUB ROOM.”
Tuning in Stations Manually
On the front panel:
1. Press FM/AM to select the band
(FM or AM).
The last received station of the selected band is
tuned in.
• Each time you press the button, the band
alternates between FM and AM.
2. Press FM/AM TUNING 5/∞ until
you find the frequency you want.
• Pressing FM/AM TUNING
5 increases the
frequency.
• Pressing FM/AM TUNING ∞ decreases the frequency.
From the remote control:
1. Press FM/AM to select the band (FM
or AM).
The last received station of the selected band is
tuned in.
• Each time you press the button, the band alternates between
FM and AM.
2. Press TUNING UP
or TUNING DOWN
until you find the
frequency you want.
• Pressing TUNING UP
increases the frequency.
• Pressing TUNING DOWN decreases the frequency.
Notes:
• When a station of sufficient signal strength is tuned in, the TUNED
indicator lights on the display.
• When an FM stereo program is received, the STEREO indicator
also lights up.
• When you hold the button (and release it) in step 2, the frequency
keeps changing until a station is tuned in.
• You can only select the same station of the same band (FM or AM)
both for the main room and sub-room operations. If you change the
station for the sub-room, it also changes for the main room (and
vice versa). This also means that if you change the station for the
sub-room while recording a broadcasting program in the main
room, recording in the main room will be interrupted.
Using Preset Tuning
Once a station is assigned to a channel number, the station can be
quickly tuned. You can preset up to 30 FM and 15 AM stations.
To store the preset stations
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
On the front panel ONLY:
1. Tune in the station you want to preset (see
“Tuning in Stations Manually” to the left).
• If you want to store the FM reception mode for this station,
select the FM reception mode you want. See “Selecting the
FM Reception Mode” on page 36.
2. Press MEMORY.
The channel number position starts flashing on the display for
about 10 seconds.
3. Press FM/AM PRESET
5/∞ to
select a channel number while the
channel number position is
flashing.
VOLUME
AUTO MUTING TUNED STEREO
SUB ROOM SPEAKERS
SUB ROOM
ANALOG
VOLUME
MAIN ROOM
AUTO MUTING TUNED STEREO L R
SPEAKERS
1
For the main room
For the sub-room
TUNING
FF/ /REW PLAY
DOWN UP
ANALOG
VOLUME
MAIN ROOM
AUTO MUTING TUNED STEREO L R
SPEAKERS
1
ANALOG
VOLUME
MAIN ROOM
AUTO MUTING TUNED STEREO L R
SPEAKERS
1
MEMORY
SUB ROOM MAIN ROOM
FM/AM
FM/AM
FM/AM TUNING
FM/AM PRESET
Receiving Radio Broadcasts
You can browse through all the stations or use the preset function to go immediately to a particular station.
•
You can use “On-screen Menu” for most of the main room operations. For details, see page 50.
EN27-36.RX-9010VBK[C]f 01.4.13, 5:39 PM 35