Operating other manufacturers’ equipment, English – JVC RX-9010VBK User Manual

Page 71

English

Operating Other Manufacturers’ Equipment

IMPORTANT:

• To operate the component(s) using the RF signals emitted from this

remote control, the IR signal transmitter and the RF rod antenna
must be connected to this receiver.
– Place the IR signal transmitter so that it is aimed at the remote

sensor on the target component(s).

– The RF signal-reachable distance may differ depending on the

operating conditions and circumstances.

– The IR signal transmitter can send signals at a distance of 10 feet

(3 m).

When using the remote control:
Check to see if TV/CATV/DBS selector are set to the correct position:

TV/CATV/DBS selector:

•

For TV operations

Set TV/CATV/DBS selector to “TV.”

•

For the CATV converter and DBS tuner
operations

Set TV/CATV/DBS selector to “CATV/DBS.”

• Check to see if the following information appear on the display

window on the remote control.

This remote control supplied with the receiver can transmit control signals for other manufacturers’ VCRs, TVs, CATV
converters, DBS tuners, DVD players ,and CD players. By changing the transmittable signals from preset ones to the
other manufacturers’, you can operate the other manufacturer’s components using this remote control.

When operating the other manufacturers’ components, refer also to the manuals supplied with them. To operate these
components with the remote control, first you need to set the manufacturer’s code each for VCR, TV, CATV converter,
DBS tuner, and DVD player.

After replacing batteries of the remote control, set the manufactures’ codes again.

Buttons

Indications

TV/DBS

VCR 1

DVD or DVD MULTI

DVD

DVD MENU

DMENU

Buttons

Indications

TV/DBS

CATV

VCR 1

DVD or DVD MULTI

DVD

DVD MENU

DMENU

Indications

DMENU

Buttons

%, fi, @, #, SET

To change the transmittable signals for
operating another manufacturer’s TV

1. Set TV/CATV/DBS selector to “TV.”

2. Press and hold TV/CATV/DBS POWER.

3. Press TV/DBS.

4. Enter manufacturer’s code using buttons 1–9,

and 0.

See page 70 to find the code.

5. Release TV/CATV/DBS POWER.

After setting TV/CATV/DBS selector to “TV,” you can perform
the following operations on the TV:

TV/CATV/DBS POWER:

Turns on and off the TV.

TV VOL +/–:

Adjusts the volume.

TV/VIDEO:

Sets the input mode (either TV
or VIDEO).

After pressing TV/DBS (with TV/CATV/DBS selector set to
“TV”), you can perform the following operations on a TV:

CHANNEL +/–:

Changes the channels.

1 – 10, 0, 100+ (+10):

Selects the channels.
The 10 button will function as the
ENTER button if your TV requires
pressing ENTER after selecting a
channel number.

Notes:

• Refer to the manual supplied with your TV.
• You may not change the channels of some TVs by pressing

number buttons. In this case, press CHANNEL +/– for
changing the channels.

6. Try to operate your TV by pressing

TV/CATV/DBS POWER.

When your TV turns on or off, you have entered the correct code.
If there are more than one code listed for your brand of TV,
try each one until the correct one is entered.

Continued to the next page.

CATV/

DBS

After setting the remote control mode selector to “TV” :

After setting the remote control mode selector to “CATV/DBS” :

After selecting a source:

After pressing DVD MENU:

When you press the buttons listed above, the indication appears
for 5 – 10 seconds for your confirmation.

Buttons

PLAY

STOP

PAUSE

1 – 9, 0, +10, 100+

CHANNEL +/–

Indications

one of the source
names listed above

VCR1 or TV

Note:

All the functions may not be assigned to the buttons in some
equipment.

EN62-74.RX-9010VBK[C]f

01.4.13, 5:40 PM