JVC RX-9010VBK - Manual (Page 61)

58
English
1 Source name: CD or MD
2 Select
or , then press SET to change the disc.
3 Track numbers and track titles.
• When you move to a track number, you can
change the track information by pressing @ / #. Each
time you press the button, track information alternates
between its track title and its performer. (You can also
start playing the track by pressing SET.)
4 Select this (move in front), then press SET to go to
the DISC SEARCH screen (see page 59).
5 Select this (move in front), then press SET to go to
the TITLE INPUT screen (see page 60).
6 This appears only when a CD Text is selected.
7 Disc information such as the disc title, performer, and
music genre.
When this is selected (
in front), you can change the
disc information by pressing @ / #. Each time you press
the button, disc information (see “Note on 7”) changes.
8 Select or , then press SET to change the track.
9 Usable buttons and their functions for the current
selection.
Indication here will be changed according to what is
currently selected (
in front) on the screen. See “Note
on 9.”
Note on 7 :
The following information will appear on the display:
• For CD Texts — Disc title, Performer, Genre, Song writer,
Composer, Arranger, Message
Only recorded information will be shown. If there is no data, “NO
DATA” will appear.
• For MDs — Disc title
If there is no data, “NO DATA” will appear.
Note on 9 :
For example, the SET button will be used to start play (PLAY), to go to
the next screen (ENTER), and to determine the selection (ENTER).
To exit from the Disc information screen:
Press EXIT.
Notes:
• The on-screen display will disappear in the following cases:
– if no operation is done for about 10 minutes.
– if you do any operation other than explained in this section.
• To control the MD recorder using the TEXT COMPU LINK remote
control system, you have to change the source name shown on the
display from “TAPE” to “MD.” (See page 33.)
• Some special characters and marks cannot be displayed correctly.
Disc Information screen
1
2
3
4
5
7
6
8
9
ON/OFF ON/OFF POWER POWER
STANDBY
TV/CATV/DBS VCR1
ON SUB ROOM MAIN ROOM
SUB ROOM MAIN ROOM
SUB ROOM MAIN ROOM
Ex. When you press TEXT DISPLAY,
“MENU” appears on the display
window.
SUB ROOM MAIN ROOM
On-Screen Operation buttons (on the remote control)
CHANNEL
TV/VIDEO
MUTING
SET
MENU
DVD
MENU EXIT
TEXT DISPLAY
TV VOL VOLUME
RM-SRX9010J REMOTE CONTROL A/V CONTROL RECEIVER
SET
MENU
DVD
MENU EXIT
TEXT
DISPLAY
“MENU” appears on the display window of the remote control
when you press the buttons — TEXT DISPLAY,
% / fi / @ /
#, SET, EXIT.
OPERATIONS:
To use this remote control system, you need to connect the TV to the
MONITOR OUT jack on the rear panel (see page 9), and set the
TV’s input mode to the proper position to which the receiver is
connected.
Make sure you have connected the CD player or
MD recorder equipped with the TEXT COMPU LINK
remote control system. If not, you cannot use the
following functions.
IMPORTANT:
Check to see if the proper indicator(s) and information appear on the
display on the front panel before/while using the buttons and controls.
For the main room operations:
• The MAIN ROOM indicator is lit.
• The source name for the sub-room is not lit on
the display.
• When using the remote control:
– Set MAIN ROOM/SUB ROOM selector to
“MAIN ROOM.”
– Check to see if the following information
appear on the display window on the remote control.
Showing the Disc Information on the TV
Screen
Press TEXT DISPLAY while “CD” or “MD” is
selected as the source.
The Disc Information screen appears on the TV.
EN50-61.RX-9010VBK[C]f 01.4.13, 5:40 PM 58