Icom IC-756 - Manual (Page 26)

23
3
FREQUENCY SETTING
■ Frequency setting with the tuning dial
■ Direct frequency entry with the keypad
• For ham band use
q Push the desired band key on the keypad 1–3
times.
- 3 different frequencies can be selected on each band
with the band key. (See “Triple band stacking register”
below.)
w Rotate the tuning dial to set the desired frequency.
e Select the desired operating mode with the mode
switch. (p. 25)
• For general coverage receiver use
q Push [GENE] on the keypad 1–3 times.
- The [GENE] key calls up a frequency for general cov-
erage receiver use.
w Rotate the tuning dial to set the desired frequency.
- For quick tuning, use the quick tuning step function. (p.
24)
e Select the desired operating mode with the mode
switch. (p. 25)
1 9.780.00 VFO VFO
USB USB
USB USB
21.025.00 21.025.00
T X T X
1 1 USB USB
ANT ANT
1
METER METER
Po Po
2.4k 9 2.8k 455 12:34
15.100.00 VFO VFO
USB USB
USB USB
21.025.00 21.025.00
T X T X
1
ANT ANT
1
METER METER
Po Po
2.4k 9 2.8k 455 12:34
21.295.00 VFO VFO
USB USB
USB USB
21.025.00 21.025.00
T X T X
1
ANT ANT
1
METER METER
Po Po
2.4k 9 2.8k 455 12:34
21.200.00 VFO VFO
USB USB
USB USB
21.025.00 21.025.00
T X T X
1 1 USB USB
ANT ANT
1
METER METER
Po Po
2.4k 9 2.8k 455 12:34
NOTE: If the dial lock function is activated, the lock indicator lights and the tuning dial
does not function. In this case, push [LOCK] to deactivate the lock function.
The transceiver has a keypad for direct frequency
entry as described below.
q Push [F-INP].
- “ ” appears.
w Input the desired frequency.
- Input “ • ” (decimal point) between the MHz units and
kHz units.
e Push [ F-INP •ENT] to enter the input frequency.
- To cancel the input, push [MAIN/SUB] instead of
[ F-INP •ENT]
[EXAMPLE]
F-inp
TRIPLE BAND STACKING REGISTER
The triple band stacking register provides 3 memories
in one band. 3 sets of a frequency and mode on each
band are automatically stored when used.
If a band key is pushed once, the last used frequency
and mode are called up. When the key is pushed
again, another stored frequency and mode are called
up.
This function is convenient when you operate 3
modes on one band. For example, one register is
used for a CW frequency, another for an SSB fre-
quency and the other one for an RTTY frequency.
[EXAMPLE]
F-INP
ENT
21.280 21.245
14.025 MHz
1 0 4 2 • 5
0 8 7 • 2 5
ENT 7 0 • 6
F-INP ENT 2 4 • 5
F-INP ENT
18.0725 MHz
1 F-INP
706 kHz
F-INP ENT • 1 5 5.100 MHz
F-INP ENT 7 7.000 MHz
21 m
21 m
14 b
14.025.00
CW
14.090.00
RTTY
14.195.00
USB
14 MHz band
Push 14 b
21.025.00
CW
21.090.00
RTTY
21.295.00
USB
21 MHz band
Push