Northern UTA220/UTA220k Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for UTA220/UTA220k Northern
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 187 |
| Size: | 1.65 MB |
Show table of contents
Document Outline
- Title Page
- PREFACE AND STATEMENT OF APPLICATION
- Contents
- Motorola Customer Information
- Chapter 1 Introduction
- FEATURES
- OPERATION
- PHYSICAL DESCRIPTION
- FUNCTIONAL
- Chapter 2 Installation
- RECEIPT INSPECTION
- SITE PREPARATION
- INSTALLATION
- DTE Connection
- DTE INTERFACE SPECIFICATIONS
- Chapter 3 Getting Started
- SWITCHES AND STRAPS
- SWITCH AND STRAP SETTINGS
- CENTRAL OFFICE SWITCH
- SETUP
- Chapter 4 ISDN
- ISDN BASICS
- Chapter 5 LCD Operation
- LCD MENUS
- LCD OPERATION
- Chapter 6 V.25 bis Dialer Operation
- OPERATION IN V.25 bis MODE
- V.25 bis MESSAGE FRAMES
- DTE INTERFACE PINS
- COMMAND PROCEDURES
- COMMANDS
- INDICATION MESSAGES
- Chapter 7 EIA-366 Dialer Operation
- CONFIGURATION
- OPERATION
- INTERFACE SIGNAL DEFINITIONS
- EXAMPLE DIAL SEQUENCE
- Chapter 8 AT Command Operation
- AT COMMAND STATEMENT
- BACKSPACE KEY
- NUMBERED COMMANDS
- Chapter 9 Rate Adaption
- RATE ADAPTION
- T-LINK
- Chapter 10 BONDING
- BONDING ON THE UTA220
- PLACING A BONDING CALL
- DISCONNECTING A BONDING CALL
- Chapter 11 Synchronous Operation
- SYNCHRONOUS MODES
- Chapter 12 D-Channel X.25
- FUNCTIONAL DESCRIPTION
- ESTABLISHING AN X.25 SESSION
- COMMON APPARENT PROBLEMS
- PAD COMMAND SET
- FACILITIES
- PAD SERVICE SIGNALS
- X.3 PARAMETERS AND VALUES
- Saving the X.3 Parameter Configuration
- Parameter 1: Pad Recall Character
- Parameter 2: Echo
- Parameter 3: Selection of Data Forwarding Characters
- Parameter 4: Selection of Idle Timer Delay
- Parameter 5: Ancillary Device Control
- Parameter 6: Control of PAD Service Signals
- Parameter 7: Action of PAD on Break from DTE
- Parameter 8: Discard Output
- Parameter 9: Padding after Carriage Return
- Parameter 10: Line Folding
- Parameter 11: Binary Speed of Local DTE
- Parameter 12: Flow Control of PAD by Local DTE
- Parameter 13: Line Feed Insertion after Carriage Return
- Parameter 14: Padding after Line Feed
- Parameter 15: Editing
- Parameter 16: Character Delete
- Parameter 17: Line Delete
- Parameter 18: Line Display
- Parameter 19: Editing PAD Service Signals
- Parameter 20: Echo Mask
- Parameter 21: Parity Treatment
- Parameter 22: Page Wait
- Chapter 13 Softload
- TA SOFTWARE ARCHITECTURE
- SOFTLOAD OPERATION
- TYPICAL LOCAL SOFTLOAD SESSION
- Chapter 14 Diagnostics
- COMMUNICATION DIAGNOSTICS
- GLOBAL TESTS
- DIAGNOSTIC STATUS DISPLAY
- Chapter 15 Maintenance
- FUSE
- MAINTENANCE
- Appendix A Specifications
- Appendix B Factory Default Settings
- Appendix C AT Command Set
- Appendix D Interfaces
- ISDN INTERFACE
- INTERFACES
- EIA-366A Requirements
- DTE INTERFACE PIN DESCRIPTIONS
- Appendix E Network Option Values
- Appendix F ASCII and EBCDIC Characters
- Appendix G Abbreviations and Acronyms
- Appendix H Status & Connection Messages
- Appendix I 128K Clear Channel Leased-Line
- Configuring D- and B-Channels
- Configuring the Port and Protocol
- Return Procedures
- Index