KEPCO BIT 232F Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for BIT 232F KEPCO
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 72 |
| Size: | 1.12 MB |
Show table of contents
Document Outline
- FIGURE 1-1. Remotely Controlled Power Supply Configurations Using Kepco Products
- SECTION 1 - INTRODUCTION
- 1.1 Scope of Manual
- 1.2 General Description
- 1.3 Specifications, BIT 232/BIT 232-F
- 1.4 Accessories
- 2.1 Unpacking and Inspection
- 2.2 Set Start-up DefaultS
- 2.3 Installation of BIT Card into the BOP
- 2.4 Input/OUtput Signals
- 2.5 RS 232 Connections
- 3.1 Equipment Required
- 3.2 Adjustment of the Bop ±10 Volt Calibration Controls (R31, R32)
- 3.3 Adjustment of the Ammeter Zero (R50)
- 3.4 Adjustment Of The Output Voltage Zero (R81)
- 3.5 Adjustment of the Full Scale Output Voltage (R21)
- 3.6 Voltage Reading Zero Calibration (R35)
- 3.7 Voltage Reading Calibration (R19)
- 3.8 Adjustment of the Output Current Zero (R83)
- 3.9 Adjustment of the Full Scale Output Current (R22)
- 3.10 Current Reading Zero Calibration (R36)
- 3.11 Current Reading Calibration (R20)
- 4.1 General
- 4.2 RS232-C Bus Protocol
- 4.3 RS232 Implementation
- 4.4 SCPI Programming
- 4.4.4.1 Keyword
- 4.4.4.2 Keyword Separator
- 4.4.4.3 Query Indicator
- 4.4.4.4 Data
- 4.4.4.5 Data Separator
- 4.4.4.6 Message Unit Separator
- 4.4.4.7 Root Specifier
- 4.4.4.8 Message Terminator
- 4.5 CIIL Programming
- 4.6 Programming Examples
- APPENDIX A - SCPI COMMON COMMAND/QUERY DEFINITIONS
- TABLE A-1. SCPI Common Command/query Index
- FIGURE A-1. *CLS — Clear Status Command
- FIGURE A-2. *ESE — Standard Event Status Enable Command
- FIGURE A-3. *ESE? — Standard Event Status Enable Query
- FIGURE A-4. *ESR? — Event Status Register Query
- FIGURE A-5. *IDN? — Identification Query
- FIGURE A-6. *OPC — Operation Complete Command
- FIGURE A-7. *OPC? — Operation Complete Query
- FIGURE A-8. *RST — Reset Command
- FIGURE A-9. *SRE — Service Request Enable Command
- FIGURE A-10. *SRE? — Service Request Enable Query
- FIGURE A-11. *STB? — Status Byte Register Query
- FIGURE A-12. *TRG — Trigger Command
- FIGURE A-13. *TST? — Self Test Query
- FIGURE A-14. *WAI — Wait-to-continue Command
- TABLE A-1. SCPI Common Command/query Index
- APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS
- TABLE B-1. SCPI Subsystem Command/query Index
- FIGURE B-1. INITiate[:IMMediate] Command
- FIGURE B-2. INITiate:CONTinuous Command
- FIGURE B-3. INITiate:CONTinuous Query
- FIGURE B-4. MEASure:CURRent? and MEASure:VOLTage? Queries
- FIGURE B-5. CURRent Command
- FIGURE B-6. CURRent Query
- FIGURE B-7. CURRent:TRIGgered Command
- FIGURE B-8. CURRent:TRIGgered Query
- FIGURE B-9. VOLTage Command
- FIGURE B-10. VOLTage Query
- FIGURE B-11. VOLTage:TRIGgered Command
- FIGURE B-12. VOLTage:TRIGgered Query
- FIGURE B-13. FUNCtion:MODE Command
- FIGURE B-14. STATus:OPERation:CONDition Query
- FIGURE B-15. STATus:OPEReration:ENABle Command
- FIGURE B-16. STATus:OPEReration:ENABle Query
- FIGURE B-17. STATus:OPERation QUERY
- FIGURE B-18. STATus:PRESet Command
- FIGURE B-19. STATus:QUEStionable? Query
- FIGURE B-20. STATus:QUEStionable:CONDition? Query
- FIGURE B-21. STATus:QUEStionable:ENABle Command
- FIGURE B-22. STATus:QUEStionable:ENABle? Query
- FIGURE B-23. SYSTem:ERRor? Query
- FIGURE B-24. SYSTem:LANGuage Command
- TABLE B-1. SCPI Subsystem Command/query Index
- APPENDIX C - CIIL COMMAND DEFINITIONS
- APPENDIX D - TERMINAL EMULATION PROGRAM
- APPENDIX E - RS232 COMMAND LOOP PROGRAM
- APPENDIX F - C LANGUAGE FUNCTIONS
- APPENDIX G - BASIC LANGUAGE TERMINAL EMULATION
- APPENDIX A - SCPI COMMON COMMAND/QUERY DEFINITIONS