Panasonic TH-86CQE1W 86" Class 4K UHD Commercial Monitor - Manual (Page 37)

English - 36 -
Wireless Connectivity
To Connect to a Wireless Network
• You must have a wireless modem/router connected
to an active broadband connection.
1
1
Broadband ISP connection
• A Wireless-N router (IEEE 802.11a/b/g/n) with
simultaneous 2.4 and 5 GHz bands is designed
to increase bandwidth. These are optimized for
smoother and faster HD video streaming, file
transfers and wireless gaming.
• The frequency and channel differ depending on
the area.
• The transmission speed differs depending on the
distance and number of obstructions between the
transmission products, the configuration of these
products, the radio wave conditions, the line traffic
and the products that you use. The transmission may
also be cut off or may get disconnected depending
on the radio wave conditions, DECT phones or any
other WLAN 11b appliances. The standard values of
the transmission speed are the theoretical maximum
values for the wireless standards. They are not the
actual speeds of data transmission.
• The location where the transmission is most effective
differs depending on the usage environment.
• The Wireless feature of the Display supports 802.11
a,b,g & n type modems. It is highly recommended
that you should use the IEEE 802.11n communication
protocol in order to avoid any possible problems while
watching videos.
• You must change your modem’s SSID when there are
any other modems around with the same SSID. You
can encounter connection problems otherwise. Use
a wired connection if you experience problems with a
wireless connection.
Configuring Wireless Device Settings
Open the Network menu and select Network Type as
Wireless Device to start connection process.
Highlight Scan Wireless Networks option and
press ENTER to start a search for available wireless
networks. All found networks will be listed. Highlight
your desired network from the list and press ENTER
to connect.
Note: If the modem supports N mode, you should set N
mode settings.
If the selected network is password-protected, enter the
correct key by using the virtual keyboard. You can use
this keyboard via the directional buttons and the ENTER
button on the remote control.
Wait until the IP address is shown on the screen.
This means that the connection is now established.
To disconnect from a wireless network, highlight
Network Type and press Left or Right buttons to set
as Disabled .
If your router has WPS, you can directly connect to
the modem/router without entering a password or
adding the network first. Highlight Press WPS on
your Wi-Fi router option and press ENTER . Go
to your modem/router device and press the WPS
button on it to make the connection. You will see a
connection confirmation on your Display once the
devices have paired. Select ENTER to proceed. No
further configuration is required.
Highlight
Internet Speed Test and press the ENTER
button to check your internet connection speed. Highlight
Advanced Settings and press the ENTER button to
open the advanced setting menu. Use directional and
numeric buttons to set. Highlight Save and press the
ENTER button to save settings when complete.
Other Information
You can also enable or disable Networked Standby
Mode feature using the related option. The status of
the connection will be displayed as Connected or Not
Connected and the current IP and MAC addresses, if
a connection is established.
Networked Standby
Mode
Wake-on-LAN (WoL) and Wake-on-Wireless LAN
(WoWLAN) are technologies that allow a device to be
turned on or woken up by a network message(magic
packet). This message is sent to the device by a
program executed on a remote device connected to
the same local area network, such as a smartphone.
Your Display is WoL and WoWLAN compatible. To
enable this feature set the Networked Standby Mode
option in the Settings/Network menu as On and set
the Power Mode option in the Signage>Power Up
Settings menu as Eco . It is necessary that both the
device, from which the network message will be sent
to the Display, and the Display are connected to the
same network. All devices must support magic packet
on the system from Access Points to the device which