Sony Sonnar T* FE 55mm f/1.8 ZA Lens User Manual
Page 23
23
Input
Set the input connector of the SDI 4K
signal.
Input1,2,3&4:
Select to use SDI IN
, SDI IN
, SDI IN
, and SDI
IN
with Quad Link. (Default
value)
Input1&2:
Select to use SDI IN
and SDI IN
with Dual Link.
Input3&4:
Select to use SDI IN
and SDI IN
with Dual Link.
Input1
1)
:
Select to use SDI 2 IN
with Single Link.
Input3
1)
:
Select to use SDI 2 IN
with Single Link.
1) Displayed only on the “SDI2 4K/UHD
Input Setting” menu. Select this
when the 12G/6G-SDI signal is
input.
Interface Format
Displays the interface format of the SDI
4K signal.
Quad-Link 3G/HD-SDI (Default
value)
Dual-Link 3G-SDI
Single-Link 12G/6G-SDI
1)
1) Displayed only on the “SDI2 4K/UHD
Input Setting” menu.
Image Division
Set the image division of the SDI 4K
signal.
Auto:
Select for the Auto setting.
(Default value)
2SI:
Select to receive images of the 2
sample Interleave system.
Square:
Select to receive images of
the Square system.
Signal Format
Select from the following when
“Interface Format” is set to “Quad-Link
3G/HD-SDI” or “Single-Link 12G/6G-
SDI.”
Auto (Default value)
422 YCbCr 10bit
444 RGB 10bit
444 YCbCr 10bit
444 RGB 12bit
444 YCbCr 12bit
444 XYZ 12bit
“422 YCbCr 10bit” is set when
“Interface Format” is set to “Dual-Link
3G-SDI.”
RGB Range Auto
Select how to set the RGB Range.
On:
Use the RGB Range according to
the input signal information.
(Default value)
Off:
Use the RGB Range that was set
in “RGB Range.”
Submenu
Setting
RGB Range
Select from the following when “RGB
Range Auto” is set to “Off” and the
RGB signal is input.
Full:
0 to 1023 (10bit) / 0 to 4095
(12bit)
Limited:
64 to 940 (10bit) / 256 to
3760 (12bit)
SDI Full Range
1)
:
4 to 1019 (10bit) /
16 to 4076 (12bit)
1) This manual regards the Full Range
signals that are scaled to the
quantized value except the inhibit
code on the SDI standard as the SDI
Full Range.
EOTF Auto
Select how to set EOTF when “Signal
Format” is set to a setting other than
“444 XYZ 12bit.”
On:
Use EOTF according to the input
signal information. When the
value of SDI Payload ID Transfer
characteristics is Unspecified,
EOTF that was set in “EOTF” is
applied.
Off:
Use EOTF that was set in “EOTF.”
EOTF
Select the gamma from the following
when “EOTF Auto” is set to “Off.”
2.2
2.4
2.6
CRT
2.4(HDR)
S-Log3(HDR)
S-Log2(HDR)
SMPTE ST 2084(HDR)
ITU-R BT.2100(HLG)
S-Log3(Live HDR)
When “ITU-R BT.2100(HLG)” is selected
HLG System Gamma:
Sets the
system gamma of the HLG. Set
from 1.000 to 1.500. (Default
value: 1.200)
Note
When “Signal Format” is set to “Auto”
or “444 XYZ 12bit” and the XYZ signal is
input, the optimum setting for the XYZ
signal is fixed.
Col. Space/Mtx.
Auto
Select how to set the color space and
transfer matrix when “Signal Format” is
set to a setting other than “444 XYZ
12bit.”
On:
Use the color space and transfer
matrix according to the input
signal information.
Off:
Use the color space and transfer
matrix that was set in the menu.
Submenu
Setting