Numerical command summary – Grass Valley Maestro Master Control Reference Manual v.2.4.0 User Manual
Page 33
MAESTRO — Automation Interface Protocol Technical Reference Manual
33
Numerical command summary
Numerical command summary
Hex
Command
C/R/U
Arguments
0x44
TX_TRIG
C/-/-
trigger_bits
0x45
TX_STAT
-/R/U
trans_status
0x48
VID_PSET
C/R/U
video_source ign
0x49
VID_SYNC
-/R/-
sync_bits
0x4A
VID_1KEY
C/R/U
key_type key_mod ign matte_mod
0x4C
VID_MODE
C/R/U
transition
0x4D
VID_RATE
C/-/-
trans_rate
0x4D
VID_RATE
-/R/U
trans_rate
0x4E
VID_2KEY
C/R/U
key_type key_mod ign matte_mod
0x50
SEL_1KEY
C/R/U
key_src
0x51
SEL_2KEY
C/R/U
key_src
0x58
AUD_PSET
C/R/U
audio_source ign
0x5A
PST_OVER
C/R/U
over_selection
0x5B
PGM_OVER
C/R/U
over_selection
0x61
REM_MODE
C/R/U
off_on_null
0x76
ALL_STOP
C/-/-
0x78
FTBLK
C/R/U
0x79
RFTB
C/-/-
0x7F
TAKE_XPT
C/R/U
bus video_source audio_source ign ign
0x90
CLK
C/R/-
time_value
0x91
PROLL
C/R/U
seconds
0xA1
LRS_PST
C/R/U
audio_mode
0xA3
LRS_PGM
C/R/U
audio_mode
0xA4
MAL_PST
C/R/U
audio_level
0xA7
MAL_PGM
C/R/U
audio_level
0xAA
RATIO
C/R/U
audio_level
0xAB
SAP0_PST
C/R/U
audio_level
0xAC
SAP1_PST
C/R/U
audio_level
0xAD
SAP0_PGM
C/R/U
audio_level
0xAE
SAP1_PGM
C/R/U
audio_level
0xC0
VID_BPSET
C/R/U
video_source ign
0xC1
AUD_BPSET
C/R/U
audio_source ign
0xC2
SWAP_PST
C/-/-
backup_bits
0xC3
SWAP_PGM
C/-/-
backup_bits
0xE1
SET_MIX
C/R/U
mixer src key_mix_bus audio_ratio ign
0xE0
SET_KEY
C/R/U
keyer video_src key_mix_bus key_type invert_mod key_shadow
matte_mod key_timing key_clip key_gain matte_hue matte_sat matte_lum
0xE2
SET_AUDIO
C/R/U
src_bus channel_bits ratio balance gain mode ch_rev phase_inv
0xE3
TRAN_PRESET
C/R/U
board_bits type rate rate_SS:FF delay_SS:FF black_SS:FF
0xE4
RECALL_REG
C/R/U
register_bits register_number
`C' = Used as a Command
`R' = Used as a READ command
`U' = Can be used with UPDATE command
`-' = not applicable as a command or a Read command, as indicated
`*' = required argument to a READ command message