AEC HE Mass Flow Series Drying hoppers - Manual (Page 45)

Page 44 HE
• CHE • BCHE Mass Flow Series Drying Hoppers
Figure 16
Default Setting List for 1/16 DIN Process Temperature Controller
Mode Parameter Setting range Default AEC setting
Level 0 SP Set Point SP Lower Limit to Upper Limit EU 0 Default
Level 0 r - S Run/Stop Run/Stop Run Default
Mode Parameter Setting range Default AEC setting
Level 1 AE AT Execute/Cancel Off/AT-1/AT-2 Off Default
Level 1 SP-0 Set Point 0 SP Lower to Upper EU 0 Default
Level 1 SP-1 Set Point 1 SP Lower to Upper EU 0 Default
Level 1 AL-1 Alarm Value 1 -1999 to 9999 EU 0 25.0
Level 1 AL-2 Alarm Value 2 -1999 to 9999 EU 0 25.0
Level 1 AL-3 Alarm Value 3 -1999 to 9999 EU 0 Default
Level 1 P Proportional Band 0.1 to 999.9 %FS 10.0 4.4
Level 1 I Integral Time 0 to 3999 SEC 233 84
Level 1 d Derivative Timer 0 to 3999 SEC 40 13
Level 1 C-SC Cooling Coefficient 0.01 to 99.99 1.00 Default
Level 1 C-db Dead Band -19.99 to 99.99 %FS 0.00 Default
Level 1 6F-r Manual Reset Value 0.0 to 100.0% 50.0 Default
Level 1 HYS Hysteresis (Heat) 0.01 to 99.99 %FS 0.10 Default
Level 1 CHYS Hysteresis (Cool) 0.01 to 99.99 %FS 0.10 Default
Level 1 CP Control Period (Heat) 1 to 99 SEC 20 Default
Level 1 C-CP Control Period (Cool) 1 to 99 SEC 20 Default
Mode Parameter Setting range Default AEC setting
Level 2 r-L Remote/Local RMT/LCL LCL Default
Level 2 SPrU Sp Ramp Time Unit M(Minutes)/H(Hour)s M Default
Level 2 SPrE Sp Ramp Set Value 0 to 9999 EU 0 Default
Level 2 LbA LBA Detection Time 0 to 9999 SEC 0 Default
Level 2 Au-5 MV at Stop -5.0 to 105.0 % 0.0 Default
Level 2 Au-E MV at PV Error -5.0 to 105.0 % 0.0 Default
Level 2 6L-H MV Upper Limit MV Lower Limit +0.1 to 105.0% 105.0 Default
Level 2 6L-L MV Lower Limit -5.0 to MV Upper Limit -0.1% -5.0 Default
Level 2 6rL MV Change Rate Limit 0.0 to 100.0 %/SEC 0.0 Default
Level 2 CnF Input Digital Filter 0 to 9999 SEC 0 Default
Level 2 ALH1 Alarm 1 Hysteresis 0.01 to 99.99% 0.02 Default
Level 2 ALH2 Alarm 2 Hysteresis 0.01 to 99.99% 0.02 Default
Level 2 ALH3 Alarm 3 Hysteresis 0.01 to 99.99% 0.02 Default
Mode Parameter Setting range Default AEC setting
Level 2 Cn5H Input Shift Upper Limit -199.9 to 999.9 °C 0.0 Default
Level 2 Cn5L Input Shift Lower Limit -999.9 to 999.9 °C 0.0 Default