Welltech IP-380 v.1.0 - Manual (Page 19)

iP380 User Manual
Welltech Technology Co., Ltd.
19 / 104 2012/11/01
number.
Remark:
 In the iP380 web management system “Phone” -> “Auto Dial” web page, check [Auto Dial]
page parameter [Key As Send], the Settings is Enable or not.
1.6.2.2. Point-to-Point(P2P) Dial Feature
Two iP380 IP-Phone devices can call directly without SIP proxy server registration mode.
Environmental requirements:

Both iP380 IP-Phone device need to use physical static network IP address ; or at the same
private LAN network environment, or in a same VPN network.
Example:
 If the called iP380 IP address is 192.168.0.160, dial number as follows:
Pick up the phone, dial “192*168*0*160”, then press “#” or wait 5 seconds to finish the
P2P call.
 If the called iP380 IP address is 192.168.1.20 and port is 5062, dial number as follows:
Pick up the phone, dial “192*168*1*20**5062”, then press “#” or wait 5 seconds to finish
the P2P call.
1.6.2.3. Hold Call
In the talking state, press [Hold] key, the phone call will retain immediately. Then, user can select
other line to make a new call.
1.6.2.4. Call Waiting
In the talking state, If user hear a call waiting tones and iP380 LCD show a new incoming call
number at the same time. User can press [Hold] key to retain original call and answer waiting call.
During the talking state, User can press [Hold] key again, the original call will be connected.
1.6.2.5. Blind Transfer
If user 『A』 and 『B』 are in a phone call, 『A』 will transfer this phone to user 『C』:
1. 『A』 press
[Trans] on iP380 device, then 『A』 can hear dial tone.
2. 『A』 enter user 『C』 phone number and press “#” Key (Or wait for 5 seconds).
3. 『A』 can hand up the phone.
1.6.2.6. Attendant Transfer (Answer then Transfer)
If user 『A』 and 『B』 are in a phone call, 『A』 will transfer this phone call and talk to user 『C』:
1. 『A』 press
[Hold] key, then hear dial tone.
2. 『A』 dial 『C』 phone number and press “#” key (Or wait for 5 seconds).
3. The user 『C』 answer the call and after talk was finished. Then 『A』 press
[Transfer] key to
complete the transfer feature.
4. If the user 『C』 doesn’t answer, 『A』 can press [Hold] key to return the phone call, then talk
『
B』.
1.6.2.7. Conference Call (3-way calling)
If user 『A』 and 『B』 are in a phone call, 『A』 want 『C』 to join this meeting:
1. 『A』 press
[Hold] key, and hear dial tone.
2. 『A』 dial 『C』 phone number and press “#” key (Or wait for 5 seconds).
3. The user 『C』 answer the call and talk. Then 『A』 press
[Conf] key to complete the 3-party
conference feature. Now 『A』、『B』、『C』 can talk in a 3-party conference room.
4. If the user 『C』 does not answer, 『A』 can press [Hold] key to return the phone call, then talk
to『B』.
5. During the conference call, If 『A』 hand up the phone call, the conference feature will be
canceled, the 『B』、『C』 disconnected immediately.