Ariens 929000 - Manual (Page 53)

»
©
HYDROSTATIC CONTROL LEVER
(Hydrostatic Models — Hgure 2)
This lever regulates both tractor speed and
direction. Gradually move the lever forward from the
"pork-start" (neutral) position to increase forward
travel speed. Move the lever rearward to the "R"
position to back the tractor and regulate reverse speed.
N O T E : T h e lin e s a n d n u m b e r s n e x t to th e fo rw a rd
s lo t d o n o t in d ica t e a g iv e n s p e e d . T h e y s e r v e a s
g u id e lin e s o n ly .
THE CQNTROL LEVER MUST BE IN THE "PARK-START'
POSITION TO START THE ENGINE.
Figure 2
®
GEAR SHIFT LEVER (Gear Shift Models) —
Figure 3
The gear shift lever is used to select any of three
forward gears or one reverse gear. The markings 1, 2, 3
and R on the control console indicate the locations of
the gears. The slowest forward gear is indicated by No.
T, the secondary gear, No. 2 and the fastest gear. No.
3. The "R" indicates reverse.
THE GEAR SHIFT LEVER MUST BE IN THE FORWARD
NEUTRAL POSITION AS SHOWN IN FIGURE 3 TO START
THE ENGINE.
©
HYDROSTATIC NEUTRALIZER AND BRAKE PEDAL
(Hydrostatic Models) — Figure 1
When this pedal is depressed, the hydrostatic
control lever will return to neutral and stop the forward
or reverse motion of the tractor. At the same time, the
pedal actuates an independent brake which provides
an additional means of stopping the tractor.
N O T E : A L W A Y S R E M O V E H A N D F R O M H Y D R O ­
S T A T IC C O N T R O L L E V E R B E F O R E D E P R E S S IN G T H E N E U ­
T R A L IZ E R A N D B R A K E P E D A L . T H E T W O C O N T R O L S A R E
IN T E R C O N N E C T E D . O P E R A T IN G T H E M S IM U L T A N E O U S ­
L Y COULD RESULT IN D A M A G E D O R M IS A D J U S T E D L IN K ­
A G E .
X X -"'*—
■ igure 4
®
CLUTCH BRAKE PEDAL (Gear Shift Models) —
Rgure 4
The clutch-brake pedal performs two functions:
1. When depressed to the "midway" range the
clutch disengages and the transmission can be shifted
to any desired gear.
2. When the clutch-brake pedal is fully depressed,
the brake actuates and stops the tractor.
N O T E : A lw a ys r e le a s e th e p e d a l s lo w ly fo r sm o o th
a c ce le r a tio n . D o n o ta llo w fo o t to r e s t o n p e d a l e x ce p t
fo r c lu tc h in g a n d b ra k in g fu n ct io n s .
BRAKE LOCK — Figures 2 and 3
A brake lock is provided on both hydrostatic and
gear shift models to prevent the tractor from
moving when parked or left unattended.
To lock the brake, push the brake lock forward
with the foot pedal fully depressed. Then release the
foot pedal. Figure 2 shows the brake lock engaged.
Figure 3 shows it disengaged.
IM P O R T A N T : E N G A G E T H E B R A K E L O C K B E F O R E
D IS M O U N T IN G F R O M T H E T R A C T O R O R A N Y T IM E IT
IS L E F T U N A T T E N D E D .
PAGE 53