Reznor RBL Option - Installation - Weather Hood Assembly - Manual (Page 8)

Form-I-OPT-WH, Page 8
3.3 OPTION AS16
for MAPS ® III
Cabinet D
Models RCB/
RDB/RDCB/
RDDB/RECB/
REDB
3.3.1 Dimensions
The Option AS16 shown fits all sizes of MAPS ® III Cabinet D Models RCB/RDB/
RDCB/RDDB/RECB/REDB.
48-11/32” (1228mm)
54-1/4”
(1378mm)
6-1/4” (159mm)
Dimensions from top of
unit and rear panel.
Side View
of Installed
Hood
FIGURE 5 -
Dimensions of
Outside Air Hood
for all Sizes of
MAPS ® III Cabinet
D Models RCB,
RDB, RDCB, RDDB,
RECB, and REDB
Option AS16 Hood Pkg P/N 222657
Components by STEP (FIGURES 6A - 6D )
Used in Qty Description P/N
STEP 1a,
FIGURE 6A
1 Top (Section 1) 222689
6 Sheetmetal Screws 11813
STEP 1b,
FIGURE 6A
1 Left Side (Section 1) 222697
1 Right Side (Section 1) 222694
12 Self-Drilling Screws 37661
STEP 1c,
FIGURE 6A
1 Bottom 222692
8 Self-Drilling Screws 37661
4 Sheetmetal Screws 18113
STEP 2a,
FIGURE 6B
1 Left Side (Section 2) 222696
1 Right Side (Section 2) 222693
10 Sheetmetal Screws 11813
Silicone 53335
STEP 2b,
FIGURE 6B
1 Top (Section 2) 222690
10 Sheetmetal Screws 11813
STEP 2c,
FIGURE 6B
1 Top Seal 222691
20 Sheetmetal Screws 11813
Silicone 53335
3.3.3 Installation
Instructions
3. Components, Dimensions, and Installation Instructions (cont'd)
Installation NOTES:
- Select screws carefully.
Use sheetmetal screws
(slotted head with straight
tip) when holes in the
cabinet are provided. Use
self-drilling screws (head
is not slotted with drill-type
tip) when matching holes
are not provided.
- Follow STEPS in order.
STEP 3a,
FIGURE 6C
1 Top Filter Support 222701
1 Top Filter Clip 222702
16 Sheetmetal Screws 11813
STEP 3b,
FIGURE 6C
1 Bottom Filter Support 222703
1 Bottom Filter Clip 222704
16 Sheetmetal Screws 11813
STEP 3c,
FIGURE 6C
1 Left Side Gutter 222698
1 Right Side Gutter 222695
18 Sheetmetal Screws 11813
STEP 3d,
FIGURE 6C
2 Vertical Supports 222700
8 Sheetmetal Screws 11813
STEP 3e,
FIGURE 6C
2 Horizontal Supports 222699
24 Sheetmetal Screws 11813
12 Clip-on Receptacles 221262
STEP 4a,
FIGURE 6D
12 Filter Stops 222705
24 Sheetmetal Screws 11813
STEP 4b,
FIGURE 6D
12 Filters, 16x16x1 104102
6 Filters, 16x25x1 101609
6 Filter Retainers 222706
12 Wing Head Screws 205707
12 Nylon Retainers 205709
3.3.2 Components,
Option AS16 for all
MAPS ® III Cabinet D
Sizes
All screw ends (except some across the bottom) should be inside the air hood. The
top and sides are in two sections; starting at the inlet air opening, follow the illustrated
instructions. Due to the size, assembly and installation requires two persons.
1. Install First Section (FIGURE 6A)
a) Top Panel - Above the air inlet opening, remove and save the factory-installed
screws attaching the system top. Slide the edge of the hood top panel underneath
the edge of the cabinet top. The edge of the hood top panel must be between
the cabinet top and the end panel. Reinsert all of the sheetmetal screws.
b) Install First Section Side Panels - Position the hood side panel under and to
the inside of the hood top panel. Attach the side panel to the system cabinet and
to the hood top. Use the type of screws shown. Screw ends should be inside the
hood.
Repeat to install the other side of the hood.
c) Install Hood Bottom (FIGURE 6A) - Position and attach the bottom as illustrated.
Use the type of screws shown.
2. Install the Second Section (FIGURE 6B)
a) Install Side Panels - Position one of the small side panels against the already
installed side panel as illustrated. Remove the small panel and apply a bead of
Applies to MAPS®III:
Models RCB, RDCB,
and RECB Sizes 360,
480, 600, and 720; and
Models RDB, RDDB,
REDB Sizes 418, 444,
484, 538, 564, 602, 658,
684, 722, 804, and 842