Reznor RBL Option - Installation - Weather Hood Assembly - Manual (Page 11)

Form I-OPT-WH, P/N 132901 R13, Page 11
FIGURE 7 - Assembled
Inlet Air Hood, Option
AS16 on a MAPS ® III D
Cabinet
(2) P/N 104102,
16x16x1
(2) P/N 104102,
16x16x1
(2) P/N 104102,
16x16x1
(2) P/N 104102,
16x16x1
(2) P/N 104102,
16x16x1
(2) P/N 104102,
16x16x1
(2) P/N 101609,
16x25x1
(2) P/N 101609,
16x25x1
(2) P/N 101609,
16x25x1
Inlet View - Option AS16, MAPSIII Size D
3.4 Option AS2, Outside Air Hood, for Models ADF/ADFH; (H)RPB; RPBL; RBA/RBL
3.4.1 Application and Components
APPLICATION by Model and Size
Option AS2 Pkg P/N 106201 106202 106203 106204 106205 106206
Models ADF/ADFH 300 500 700/1200
Models (H)RPB 125 150/175 200/225 250/300 350 400
Models RPBL 500/600 700/1050 400/800/1200
Blower Cabinet Model RBA RBL
Components:
Right Side Panel (1) 100217
Left Side Panel (1) 100216
Top Panel (1) 100227 (1) 100228 (1) 100229 (1) 100230 (1) 100231 (1) 100232
Bottom Panel (1) 100234 (1) 100235 (1) 100236 (1) 100237 (1) 100238 (1) 100239
Screened Louver Assembly (1) 103773 (1) 103774 (1) 103775 (1) 103776 (1) 103777 (1) 103778
Sheetmetal Screws #10x1/2" lg (29) 11813
*Support Angle (factory-installed) 105010 105011 105012 105013 105014 105015
*The support angle is not included in the option package. When a unit is ordered with an Option AS2 outside air hood, the
support angle is attached to the cabinet at the factory. The slotted holes will allow for any adjustment required when Option
AS2 outside air hood is installed.
4. Install Filter Stops, Filters (not illustrated here; see FIGURE 7), and Filter
Retainers (FIGURE 6D)
a) Install 12 Filter Stops - Position the filter stops on the vertical supports. Attach
filter stops with sheetmetal screws but do not tighten.
b) Install the 18 Filters and six Filter Retainers - Starting with either the bottom or
the top row, position two filters in an opening, adjust stop, remove filters, tighten
stop, and return filters to position. Holding filters in place, use nylon retainers,
wing head screws, and the clip-on retainers installed in STEP 3E to secure the
filter retainer. Install the other filters in that row. Install the other two rows of filters
and their retainers.
3.4.2 Installation
Instructions, Option
AS2 (Refer to
FIGURES 8A, 8B,
and 8C.)
1. Install Top Panel - On the air inlet end of the cabinet, remove the row of factory-
installed screws attaching the cabinet top. Slide the hood top panel under the
edge of the cabinet top. The edge of the hood top panel must be between the
cabinet top and end panel. Reinsert all of the sheetmetal screws.
2. Install Side Panels - Slide the hood right side panel into the slot between the
cabinet end panel and corner leg (See FIGURE 8A). Be sure that the side panel
is under and to the inside of the hood top panel. Attach to the cabinet and the
hood top using the required number of sheetmetal screws. Repeat with the left
side panel.
3. Install Bottom Panel - Position the hood bottom panel so that it is to the inside
of the two side panels and above the factory-installed support angle. Attach to
both side panels.