Great Planes CAP 232 40 Kit - GPMA0232 - Manual (Page 4)

❏
Fuelproof paint; See Painting (page xxxx)
❏
Medium Fuel Tubing (GPMQ4131, 3')
❏
1/4" Latex Foam Rubber Padding (HCAQ1000)
❏
1/16" Foam Wing Seating Tape (GPMQ4422)
❏
10 oz. Fuel Tank (GPMQ4104)
❏
(2) 2-1/2" Wheels (GPMQ4223)
❏
(1) 3/16" Wheel Collar (GPMQ4308)
❏
(2) 3/32" Wheel Collars (GPMQ4303)
❏
2-1/2" Spinner (GPMQ4517 – red)
❏
Pilot (Williams Bros. 1/5 Scale Sportsman Pilot used
in prototype, WBRQ2626)
❏
Fueling System (Great Planes Top Fueler, ™ GPMQ4160)
❏
Pacer Formula 560 Canopy Glue
❏
1" Tail wheel (GPMQ4241)
These are the building tools, glue, etc. that we recommend
and mention in the manual.
We recommended Great
Planes Pro ™ CA and Epoxy
❏
2 oz. Thin CA (GPMR6003)
❏
2 oz. Medium CA+ (GPMR6009)
❏
CA Accelerator (GPMR6035)
❏
30-Minute Pro Epoxy (GPMR6047)
❏
Building Square (HCAR0480)
❏
Plan Protector (GPMR6167)
❏
#1 Hobby Knife Handle (HCAR0105)
❏
#11 Blades (HCAR0311, 100 qty.)
❏
Razor Saw
❏
Small T-pins (HCAR5100)
❏
Medium T-pins (HCAR5150)
❏
Masking Tape
❏
Electric Power Drill
❏
1/4-20 Tap (GPMR8105, drill bit included)
❏
Drill Bits: 1/16", 3/32", 7/64", 1/8", 5/32", #18 or
11/64", 3/16", #10 or 13/64" (unless purchased with
1/4-20 Tap listed above), 7/32", 1/4", 17/64"
❏
Pliers
❏
Monofilament String for aligning wing and stabilizer
❏
Screwdrivers (Phillips and Flat Blade)
❏
HobbyLite ™ Balsa Filler (HCAR3401)
❏
Sealing Iron (TOPR2100)
❏
Bar Sander or Sanding Block and Sandpaper (coarse,
medium, fine grit)
❏
Microballoons
In our busy wor k shop we use the Great Planes
Easy-Touch
™ Bar Sanders equipped with Great Planes
#80, #150 and #220-grit Easy-Touch Adhesive-Backed
Sandpaper. Great Planes Easy-Touch Bar Sanders are
made from lightweight, rigid, extruded aluminum and can
be found at most hobby shops.
They are available in three sizes–5-1/2" (GPMR6169) and
11" (GPMR6170) for most general purpose sanding and
22" (GPMR6172) for long surfaces such as wing leading
edges. The Easy–Touch Adhesive-Backed Sandpaper
comes in 2" x 12' rolls of 80-grit (GPMR6180), 150-grit
(GPMR6183), 220-grit (GPMR6185) and an assortment
pack of 5-1/2" long strips (GPMR6189) for the short Bar
Sander. The adhesive backed sandpaper is easy to apply
and remove from your sanding bar when it's time
for replacement.
This setup is all that is required for almost any sanding
task. Custom sanders can be made from balsa or
hardwood blocks and sticks for sanding difficult to reach
spots. We also keep some #320-grit wet-or-dry sandpaper
for finish sanding just before covering.
❏
1 oz. Thick CA- (GPMR6014)
❏
6-Minute Pro Epoxy (GPMR6045)
❏
CA Applicator Tips (HCAR3780)
❏
Epoxy Brushes (GPMR8060)
❏
Epoxy Mixing Sticks (GPMR8055, qty. 50)
❏
CA Debonder (GPMR6039)
❏
Hot Sock (TOPR2175)
❏
Trim Seal Tool (TOPR2200)
❏
Heat Gun (TOPR2000)
❏
Single Edge Razor Blades (HCAR0312, 100 qty.)
❏
Razor Plane (MASR1510)
❏
Straightedge (Fourmost Non Slip, FORR2149)
❏
1/8" Brass Tube, see page 17, step 10
❏
5/32" Brass Tube, see page 33, step 15
❏
Denatured or Isopropyl Alcohol (for epoxy clean-up)
❏
Dremel MultiPro ™ or similar w/Sanding Drum, Cutting
Burr, Cut-off Wheel
❏
Kyosho ® Curved Scissors for trimming Cowl, Wheel
Pants and Canopy (KYOR1010)
Optional Supplies and Tools
Building Supplies and Tools
4